AEG Dishwasher Error i50
⚡ Quick Answer: The AEG dishwasher i50 error indicates a malfunction in the circulation pump and/or its control electronics. This error occurs when the pump fails to ... ✅ DIY Fixable
What Does Error i50 Mean?
The AEG dishwasher i50 error indicates a malfunction in the circulation pump and/or its control electronics. This error occurs when the pump fails to operate correctly, often resulting in the inability to start wash cycles, lack of circulation noise, or incomplete cleaning of dishes. Essential troubleshooting includes checking for blockages in the pump area and ensuring proper operation of the pump motor and electronics.
Common Symptoms:
- Dishwasher displays i50 on the control panel or blinks five times and beeps.
- Dishwasher may not start a normal wash cycle.
- Lack of pump noise (circulation) during expected operation.
- Dishwasher may not wash dishes thoroughly or cycle may stop.
Possible Causes
- Blocked or obstructed circulation pump (debris in pump area) (high)
- Faulty circulation pump motor or pump component (high)
- Pump control electronics failure (triac or control board issue) (medium)
How to Fix Error i50
DIY Fix Basic checks and reset
- Turn off the dishwasher and disconnect it from mains power (unplug or switch off circuit breaker) for ~1 minute.
- Check and clean all internal filters and sump area to remove debris.
- Ensure hoses are not kinked and the water tap feeding the dishwasher is fully open.
- Reconnect power and start a wash cycle to see if the error clears.
Technician Only Inspect and repair pump assembly and electronics
- Disconnect power and access the pump area by removing the lower access panel.
- Visually inspect and test the circulation pump and associated wiring connections for damage, burn marks, or looseness.
- Measure pump motor resistance to detect open or shorted windings and replace pump if necessary.
- If pump tests ok, inspect main control PCB motor drive components (triac/transistor) and repair/replace control board as required.
Parts needed: Circulation pump assembly, Pump motor, Control board (if electronics failure identified), Wiring harness/connectors
- If the i50 error persists after cleaning filters and resetting.
- If inspection reveals burnt wiring, damaged pump components, or uncertain electrical faults.
- If you are not comfortable performing electrical or mechanical diagnostics.
Next step
Choose the next step for i50
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Dishwasher Circulation Pump
Circulates pressurized water through the dishwasher spray arms during the wash cycle.
- Typical part-only price
- $90 - $220
- DIY difficulty
- Hard
- Estimated time
- 60-120 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other components that may be involved
Check these only if your diagnosis points to them.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Technical Specifications
| wattage | 30W |
|---|---|
| component | Drain Pump |
| resistance | 20-30 ohms |
| part_number | AEG 5020000001 |
| voltage_rating | 230V AC |
Common Questions
What does i50 error mean on AEG dishwasher?
The i50 error signifies a malfunction in the circulation pump or its control electronics, affecting wash cycles.
Can I fix AEG dishwasher i50 error myself?
Yes, you can perform basic checks like cleaning filters and resetting the dishwasher.
How much does it cost to fix i50 error?
The estimated repair cost for the i50 error ranges from $150 to $450, depending on various factors.
When should I call a technician for i50?
Call a technician if the error persists after cleaning or if there are signs of burnt wiring or damaged components.
Sources & References
- AEG Dishwasher displays error code i50 (official)
- AEG Geschirrspüler Fehlercode i50 (German support) (official)
Data last verified: 2026-07-26
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!