White-Westinghouse Washing Machine Error E62
⚡ Quick Answer: The White Westinghouse Washing Machine error E62 indicates an over-temperature condition during the wash cycle, often leading to unusual grinding soun... ✅ DIY Fixable
What Does Error E62 Mean?
The White Westinghouse Washing Machine error E62 indicates an over-temperature condition during the wash cycle, often leading to unusual grinding sounds and the machine failing to spin. This error is triggered when the water temperature exceeds approximately 88°C, causing the machine to enter a safety drain mode. Common causes include a malfunctioning temperature sensor or issues with the heating element. Basic troubleshooting steps include resetting the machine and checking the water supply temperature.
Common Symptoms:
- Error E62 displayed during a wash cycle
- Machine entering safety drain and stopping with door unlocked
- Potentially elevated water temperature detection
Possible Causes
- Over‑temperature detected (NTC/temperature sensor triggered) (medium)
- Faulty temperature sensor (NTC) or sensor wiring (medium)
- Heating element or control malfunction causing runaway heat (low)
How to Fix Error E62
DIY Fix Perform basic safety checks and reset
- Turn off and unplug the washer for 5–10 minutes to reset control logic.
- Ensure water supply temperature is not excessively hot (use mixed or cold water).
- Restart a wash cycle and see if error returns.
- Observe if load size or wash program selection might contribute to higher temperatures.
Technician Only Inspect temperature sensing and heating control system
- Access internal temperature sensor (NTC) and inspect wiring harness for corrosion, breaks, or loose connectors.
- Test the NTC sensor resistance versus expected values at room temperature with a multimeter.
- Verify heating element behavior and control board outputs during a test cycle.
- Replace faulty temperature sensor or repair wiring as required, then verify error resolution.
Parts needed: NTC temperature sensor, Wiring harness/terminals, Control board/heating relay (if necessary)
- If error persists after basic resets and there is **smoke, burning smell, steam, leaks, or excessive heat**
- If you are not experienced with washer internal diagnostics or electrical measurements
Next step
Choose the next step for E62
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does E62 error mean on White Westinghouse Washing Machine?
E62 indicates an over-temperature issue during the wash cycle, causing the machine to stop.
Can I fix White Westinghouse Washing Machine E62 error myself?
Yes, try resetting the machine and checking the water temperature before seeking professional help.
How much does it cost to fix E62 error?
Repair costs for E62 error range from $50 to $250, depending on the fault and necessary parts.
When should I call a technician for E62?
Call a technician if the error persists after resets or if you notice smoke, burning smells, or leaks.
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!