Speed Queen Dryer Error ID
⚡ Quick Answer: The Speed Queen Dryer ID error indicates a malfunction related to the control board, often due to an incorrect or mismatched control board installed. ... ✅ DIY Fixable
What Does Error ID Mean?
The Speed Queen Dryer ID error indicates a malfunction related to the control board, often due to an incorrect or mismatched control board installed. This error typically appears shortly after the cycle begins, preventing the dryer from operating normally. If you've recently swapped or serviced the control board, this may be the cause of the issue. Proper identification and replacement with the correct control board can resolve the problem.
Common Symptoms:
- Error appears on display shortly after cycle start
- Dryer does not proceed with normal operation
- Control board swap or service was done recently
Possible Causes
- Incorrect control board installed (Board ID mismatch) (medium)
How to Fix Error ID
DIY Fix Power cycle to clear temporary error
- Turn the dryer off and unplug it from the power source.
- Wait 60 seconds.
- Plug it back in and power up the dryer.
Technician Only Verify and replace control board with correct ID
- Confirm the displayed ID error corresponds to a control board mismatch.
- Check part numbers of installed control board vs manufacturer specifications.
- Replace control board with correct model specified for this dryer.
- Power cycle the unit and confirm no ID error recurs.
Parts needed: Control board (correct model), Screws/fasteners, Harness connectors
- If error persists after power cycling
- If control board was recently replaced or suspected incorrect part
- If other error codes accompany ID error
Next step
Choose the next step for ID
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
- Typical part-only price
- $120 - $280
- DIY difficulty
- Medium
- Estimated time
- 20-40 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Model-compatible Dryer parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dryer Vent Cleaning Kit
Helps remove routine lint buildup from an accessible dryer vent path. It does not diagnose or repair an E-code or failed component.
Lint Trap Cleaning Brush
A narrow brush for routine cleaning around an accessible lint screen and housing.
Dryer Vent Hose Kit
A replacement exhaust duct option for visibly crushed or damaged external venting. Check diameter, length, local code, and installation clearance.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | N/A |
|---|---|
| component | Moisture Sensor |
| resistance | 5-10 ohms |
| part_number | SQ-MOISTURE-SENSOR-001 |
| voltage_rating | 120V AC |
Common Questions
What does ID error mean on Speed Queen Dryer?
It indicates a control board malfunction due to a mismatch with the installed board.
Can I fix Speed Queen Dryer ID error myself?
Yes, you can power cycle the dryer by unplugging it for 60 seconds.
How much does it cost to fix ID error?
The estimated repair cost ranges from USD 150 to 400 for parts and labor.
When should I call a technician for ID?
Call if the error persists after power cycling or if you suspect a recent incorrect control board replacement.
Data last verified: 2026-07-22
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!