Solt Dishwasher Error E4
⚡ Quick Answer: The Solt Dishwasher E4 error indicates a potential issue with the drain pump, often resulting in the dishwasher stopping mid-cycle and failing to drai... ✅ DIY Fixable
What Does Error E4 Mean?
The Solt Dishwasher E4 error indicates a potential issue with the drain pump, often resulting in the dishwasher stopping mid-cycle and failing to drain water properly. Symptoms may include unusual noises during operation and possible water accumulation detected by safety sensors. Common causes include water overflow in the base pan, drainage problems like a blocked drain hose, or a malfunctioning float switch or water level sensor. Proper troubleshooting can help identify and resolve these issues.
Common Symptoms:
- Dishwasher stops mid‑cycle when E4 displayed (general pattern from other brands)
- Water drainage attempts without normal operation (general cases)
- Possible water accumulation/overflow detected by sensors
Possible Causes
- Water overflow / leak in base pan triggering safety sensor (medium)
- Drainage issues such as blocked drain hose or pump problems (medium)
- Float switch or water level sensor malfunction (medium)
How to Fix Error E4
DIY Fix Check for obvious water overflow and reset
- Turn off and unplug the dishwasher.
- Check the base pan for water — if present, carefully tip the machine slightly to drain (if safe/feasible).
- Allow the dishwasher to dry fully before powering back on.
- Run a short cycle to see if error clears.
DIY Fix Inspect drain hose and filter
- Turn off power to the dishwasher.
- Locate and inspect the drain hose for kinks, twists, or visible blockages.
- Remove and clean the dishwasher filter according to user manual instructions.
- Reassemble and run a drain or rinse cycle to test.
Technician Only Test and potentially replace float switch / water level sensor
- Disconnect power and water supply.
- Remove dishwasher access panel to locate float switch or water level sensor.
- Test the component for free movement and correct electrical continuity.
- Replace the sensor if it fails movement or continuity tests.
Parts needed: Float switch / water level sensor
Technician Only Check drain pump and inlet systems
- Power down the appliance and disconnect from power.
- Access the drain pump and inlet assembly.
- Inspect and test the drain pump motor and water inlet valve for faults.
- Clean or replace components as indicated by tests.
Parts needed: Drain pump, Water inlet valve
- If water remains in the base pan after initial checks
- If error reappears after basic user troubleshooting
- If unusual noises or smells accompany the error code
Next step
Choose the next step for E4
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Float Switch
Detects the maximum water level to prevent overflow and potential flooding.
- Typical part-only price
- $15 - $40
- DIY difficulty
- Easy
- Estimated time
- 10-20 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Pressure Switch
Detects the water level inside the tub and signals when to start or stop filling.
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does E4 error mean on Solt Dishwasher?
E4 error indicates a malfunction in the drain pump, leading to mid-cycle stops and drainage failures.
Can I fix Solt Dishwasher E4 error myself?
Yes, check for water overflow, inspect the drain hose for blockages, and clean the filter.
How much does it cost to fix E4 error?
The estimated repair cost ranges from ¥5,000 to ¥15,000 depending on parts and labor.
When should I call a technician for E4?
Call a technician if water remains in the base pan after checks or if the error reappears.
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!