Smeg Dishwasher Error E07
⚡ Quick Answer: The Smeg Dishwasher error E07 points to a malfunction in the drain system, often related to issues with the flow meter or drainage components. Symptom... ✅ DIY Fixable
What Does Error E07 Mean?
The Smeg Dishwasher error E07 points to a malfunction in the drain system, often related to issues with the flow meter or drainage components. Symptoms include the dishwasher stopping mid-cycle, failure to complete a cycle, and potential water circulation problems. You may also notice unusual noises or other water level-related symptoms. Addressing this error typically involves checking for blockages, cleaning filters, and inspecting the drain pump.
Common Symptoms:
- Dishwasher stops mid‑cycle showing E07
- Cycle fails to progress or complete
- Possible lack of water circulation or detection
- May coincide with other water level or drain symptoms
Possible Causes
- Flow meter fault or incorrect flow sensor detection (medium)
- Drainage or water distribution issue (clog/blockage/flood sensor) (medium)
How to Fix Error E07
DIY Fix Basic checks and restart
- Turn off and unplug the dishwasher for a few minutes to reset internal electronics.
- Check that the water supply is on and inlet hose is not kinked.
- Inspect and clean any visible filters and check the drain hose for blockages or kinks.
Technician Only Inspect and test flow meter and water handling components
- Access the water inlet assembly to locate the flow meter (if fitted) and inspect for signs of corrosion or mechanical failure.
- Test flow sensor signals and wiring continuity back to the control board.
- Check drain pump and water distribution valves for blockages, proper operation, and correct installation.
- Replace defective flow meter or associated sensors as needed.
Parts needed: Flow meter / flow sensor, Water inlet valve, Drain pump and hoses
- If you are not comfortable inspecting internal components after disconnecting power
- If after basic checks and resets E07 persists
- If there are signs of leaks, strange noises from pumps, or other unusual behavior
Next step
Choose the next step for E07
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
- Typical part-only price
- $25 - $60
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other components that may be involved
Check these only if your diagnosis points to them.
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Technical Specifications
| wattage | 30W |
|---|---|
| component | Drain Pump |
| resistance | 10-30 ohms |
| part_number | Smeg 610020114 |
| voltage_rating | 230V AC |
Common Questions
What does E07 error mean on Smeg Dishwasher?
E07 indicates a drain system malfunction, often linked to the flow meter or drainage issues.
Can I fix Smeg Dishwasher E07 error myself?
Yes, you can perform basic checks like inspecting filters, hoses, and resetting the appliance.
How much does it cost to fix E07 error?
Repair costs vary; typically, flow sensor parts and technician labor are moderate.
When should I call a technician for E07?
Call a technician if the error persists after basic checks, or if you notice leaks or unusual noises.
Data last verified: 2026-07-22
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!