Samsung Washing Machine Error CE
⚡ Quick Answer: The Samsung Washing Machine CE error indicates a potential issue with the motor speed sensor, often leading to the machine stopping mid-cycle. This co... ✅ DIY Fixable
What Does Error CE Mean?
The Samsung Washing Machine CE error indicates a potential issue with the motor speed sensor, often leading to the machine stopping mid-cycle. This code may also be associated with incorrect water temperature readings, particularly during fill, drain, or spin stages, and can manifest with unusual sounds. To address this, check that the water hoses are correctly connected and perform a reset by unplugging the machine for five minutes before running a simple cycle.
Common Symptoms:
- Machine stops mid‑cycle with CE shown
- Temperature sensing anomalies reported (too hot/incorrect water temp)
- CE often appears around fill/drain/spin stages
Possible Causes
- Temperature sensor or water temperature detection issue (medium)
How to Fix Error CE
DIY Fix Check water supply and hoses
- Turn off and unplug the washing machine.
- Confirm cold and hot water hoses are connected to the correct inlets.
- Ensure hoses are secure and not leaking.
- Restart machine and run a cold wash cycle to see if code persists.
DIY Fix Reset and rerun a simple cycle
- Unplug the washer for at least 5 minutes.
- Plug it back in and select a basic wash cycle with cold water only.
- Observe if CE recurs.
Technician Only Inspect/replace temperature sensor and inlet valve
- Disconnect power to the washer.
- Access the internal temperature sensor (thermistor) and test resistance with multimeter per service manual specs.
- Inspect cold water inlet valve for proper functioning.
- Replace faulty components if out of spec.
Parts needed: Thermistor / temperature sensor, Water inlet valve
Technician Only Diagnose control board / motor circuit if temp and inlet are fine
- Use service diagnostic mode if available to read errors.
- Measure current draw on motor and heater circuits.
- Check main control board for faults or failed components.
- Replace parts as needed.
Parts needed: Control board, Motor assembly
- If CE persists after verifying water connections and basic reset
- If water temperature sensor or inlet valve tests out of specification
- If electrical diagnostics point to control board faults
Next step
Choose the next step for CE
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Thermistor
Measures precise temperature changes and sends resistance feedback to the control board.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does CE error mean on Samsung Washing Machine?
CE error indicates a motor speed sensor issue, causing the machine to stop mid-cycle.
Can I fix Samsung Washing Machine CE error myself?
Yes, check water connections and reset the machine as initial troubleshooting steps.
How much does it cost to fix CE error?
Repair costs typically range from $50 to $200, depending on the issue.
When should I call a technician for CE?
Call a technician if the CE error persists after basic troubleshooting or if electrical diagnostics indicate control board issues.
Sources & References
- Samsung Washer Error Code CE (Cooling Error) (community)
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!