Kenmore Oven Error F6
⚡ Quick Answer: The Kenmore oven F6 error indicates a malfunction in the control board, often due to a communication error between the electronic oven control and the... ✅ DIY Fixable
What Does Error F6 Mean?
The Kenmore oven F6 error indicates a malfunction in the control board, often due to a communication error between the electronic oven control and the touchpad/display. Symptoms include an erratic display, failure to respond to settings, or indications of overheating. If the oven becomes too hot, it may shut down to prevent damage. Addressing this issue may require inspecting the control board, touchpad, or temperature sensor.
Common Symptoms:
- Oven displays F6 and the control panel is blank or erratic during normal use (e.g., no proper display response).
- Oven may indicate overheating or shut down if running.
- Error can appear with display irregularities rather than specific temperature runaway in some reported cases.
Possible Causes
- Communication error between touchpad/control board (medium)
- Over‑temperature condition detected (upper oven too hot) due to sensor or control logic (medium)
How to Fix Error F6
DIY Fix Basic power reset and check panel responsiveness
- Turn off the oven and disconnect power at circuit breaker or unplug from wall.
- Wait 1–2 minutes to allow internal components to reset and capacitors to discharge.
- Restore power and observe if the F6 error reappears.
- Note if the display becomes responsive or erratic behavior persists.
Technician Only Inspect control board communication and temperature sensor
- Disconnect power and remove control panel back cover.
- Inspect and reseat ribbon cable(s) between the touchpad/display and electronic oven control board; clean contacts if needed.
- Test the upper oven temperature sensor resistance with a multimeter at room temperature; compare to expected resistance range (manufacturer spec varies by model).
- If sensor reading is out of range, replace the upper oven temperature sensor.
- If sensor is good but F6 persists, inspect EOC display driver and logic board; replace faulty control components as needed.
Parts needed: Ribbon/display cable, Touchpad/display assembly, Upper oven temperature sensor, Electronic oven control board
- If you are uncomfortable opening the control panel or working near electrical components.
- If the error persists after basic resets and visible inspection of connectors.
- If oven overheats unexpectedly during operation even without displaying the FL6 code.
Next step
Choose the next step for F6
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Model-compatible Oven parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Non-Scratch Cooktop Cleaner
A routine surface-care product. Confirm that it is approved for the specific glass, ceramic, enamel, or stainless finish.
Oven Thermometer
A diagnostic aid for comparing cavity temperature during a controlled check. It does not prove which internal component has failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | N/A |
|---|---|
| component | Control Board |
| resistance | N/A |
| part_number | WB27X11215 |
| voltage_rating | 120V AC |
Common Questions
What does F6 error mean on Kenmore oven?
F6 indicates a control board malfunction or overheating, leading to erratic display and unresponsive settings.
Can I fix Kenmore oven F6 error myself?
Yes, you can try a power reset by disconnecting the oven from power for 1-2 minutes.
How much does it cost to fix F6 error?
Repair costs for the F6 error range from $50 to $450, depending on the required parts.
When should I call a technician for F6?
Call a technician if the error persists after resets, or if you’re uncomfortable working with electrical components.
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!