Kelvinator Dishwasher Error E06
⚡ Quick Answer: The Kelvinator dishwasher error E06 indicates a malfunction in the drain pump, often caused by an overflow or excessive water level. During operation,... ✅ DIY Fixable
What Does Error E06 Mean?
The Kelvinator dishwasher error E06 indicates a malfunction in the drain pump, often caused by an overflow or excessive water level. During operation, you may notice unusual noises or the program stopping mid-cycle as the dishwasher detects too much water. Common causes include a malfunctioning water level sensor or float assembly, which may require inspection and repair.
Common Symptoms:
- Dishwasher detects too much water or water level above normal during cycle
- Program may stop mid‑cycle when error displays
Possible Causes
- Malfunctioning water level sensor or float assembly (low)
How to Fix Error E06
DIY Fix Check for overfill and water level issues
- Turn off the dishwasher and disconnect from power.
- Check the float assembly inside the dishwasher tub (if visible) to ensure it moves freely and is not stuck.
- Inspect the water inlet hose for kinks or obstructions that could cause overfilling.
- Ensure that the dishwasher is level; adjust feet if necessary so water does not pool in one area.
Technician Only Inspect water level sensor and float switch
- Verify correct operation of the float switch and water level sensor with a multimeter.
- Inspect wiring harnesses connected to the sensor and control board for damage or loose connections.
- Replace any failed water level sensor or float assembly parts if measurements are out of specification.
Parts needed: Water level sensor / float assembly, Associated wiring harnesses
- If water continues to enter the dishwasher even when the float assembly is functioning, or if internal components show signs of electrical failure.
- If no access to safely test water level sensors or if error persists after basic checks.
Next step
Choose the next step for E06
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Pressure Switch
Detects the water level inside the tub and signals when to start or stop filling.
- Typical part-only price
- $25 - $65
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Float Switch
Detects the maximum water level to prevent overflow and potential flooding.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 50W |
|---|---|
| component | Drain Pump |
| resistance | 10-20 ohms |
| part_number | KDFE204HPS-PUMP |
| voltage_rating | 120V AC |
Common Questions
What does E06 error mean on Kelvinator dishwasher?
E06 indicates a malfunction related to excessive water levels, causing the dishwasher to stop mid-cycle.
Can I fix Kelvinator dishwasher E06 error myself?
Yes, check for overfill, inspect the float assembly, and ensure the water inlet hose is clear.
How much does it cost to fix E06 error?
Estimated repair costs range from $40 to $120 for parts, plus labor.
When should I call a technician for E06?
Call a technician if water continues to enter despite checks or if internal components show electrical failure.
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!