Ilve Dishwasher Error E8
⚡ Quick Answer: The Ilve dishwasher error E8 signals a malfunction in the drain pump, often due to insufficient water levels in the wash tub. This can lead to the spr... ✅ DIY Fixable
What Does Error E8 Mean?
The Ilve dishwasher error E8 signals a malfunction in the drain pump, often due to insufficient water levels in the wash tub. This can lead to the spray arms not rotating properly and unusual noises during operation. To resolve this issue, check for water supply restrictions and ensure the inlet hose is not kinked or blocked.
Common Symptoms:
- Error E8 displayed during operation
- Water level appears too low in the wash tub
- Spray arms may not rotate properly due to insufficient water
Possible Causes
- Insufficient water entering the dishwasher (medium)
- Potential water supply or inlet restriction (medium)
How to Fix Error E8
DIY Fix Check water supply and basic fill conditions
- Ensure the water supply valve under the sink is fully open.
- Check that the water inlet hose is not kinked or blocked.
- Start a wash cycle and listen/observe if water begins to fill.
- Verify that dishes or objects are not blocking spray arm rotation.
Technician Only Inspect and test internal water inlet and fill components
- Disconnect power and water supply.
- Inspect and, if necessary, clean the water inlet valve and hose connections.
- Check the float switch and water level sensor for proper movement and signal.
- Test the circulation pump and spray arms for proper operation after water entry is ensured.
Parts needed: Water inlet valve, Float switch / water level sensor, Hoses and filters, Circulation pump and spray arms
- If after basic checks the dishwasher still shows E8 and fails to fill properly
- If there are signs of leaks, flooding, or electrical faults during inspection
- If internal components like the inlet valve or sensors fail testing
Next step
Choose the next step for E8
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
- Typical part-only price
- $25 - $60
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other components that may be involved
Check these only if your diagnosis points to them.
Float Switch
Detects the maximum water level to prevent overflow and potential flooding.
Dishwasher Circulation Pump
Circulates pressurized water through the dishwasher spray arms during the wash cycle.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Technical Specifications
| wattage | 50W |
|---|---|
| component | Drain Pump |
| resistance | 10-30 ohms |
| part_number | Ilve 123456789 |
| voltage_rating | 240V AC |
Common Questions
What does E8 error mean on Ilve dishwasher?
E8 error indicates insufficient water levels in the wash tub, causing the spray arms to malfunction.
Can I fix Ilve dishwasher E8 error myself?
Yes, you can check the water supply valve, ensure the inlet hose is clear, and observe if water fills during a cycle.
How much does it cost to fix E8 error?
Repair costs for E8 error typically range from $100 to $300, depending on parts and labor.
When should I call a technician for E8?
Call a technician if E8 persists after basic checks, or if you notice leaks, flooding, or electrical issues.
Data last verified: 2026-04-23
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!