Hisense Dishwasher Error ED
⚡ Quick Answer: The Hisense dishwasher error code ED indicates a malfunction in the drain pump, which may result in the dishwasher stopping its operation. Users might... ✅ DIY Fixable
What Does Error ED Mean?
The Hisense dishwasher error code ED indicates a malfunction in the drain pump, which may result in the dishwasher stopping its operation. Users might notice unusual sounds during the cycle or experience failure to drain water effectively. To troubleshoot, ensure the dishwasher door is fully latched, perform a power reset by disconnecting power for a few minutes, and check for any obstructions. If the issue persists, further inspection of internal components may be necessary.
Common Symptoms:
- Dishwasher stops operation and displays ‘ED’ error, preventing normal cycle progression
Possible Causes
- Drain Pump
- Blocked Drain Hose
- Faulty Control Board
How to Fix Error ED
DIY Fix Confirm error and basic checks
- Turn off the dishwasher and disconnect power (unplug or breaker off) for a few minutes.
- Reconnect power and attempt to start a new cycle to see if the ED code clears.
- Ensure the dishwasher door is fully latched and not obstructed when attempting to start a cycle.
Technician Only Inspect for water in base tray and leak/flood sensor activation
- Remove dishwasher from cabinetry if accessible.
- Check for water accumulation in the base pan under the unit (water may trigger anti-flood detection).
- If water is present, carefully drain it or tilt the dishwasher to allow base water to exit.
- Inspect flood/leak sensor and wiring harness for damage or constant closure.
- Test and verify leak detection components and related wiring with appropriate diagnostic tools.
Parts needed: flood/leak sensor, float switch assembly, base pan Moisten sensor, wiring harness
- If the error persists after basic troubleshooting and power reset
- If water damage or internal leaks are detected
- If internal sensors or wiring appear damaged
Next step
Choose the next step for ED
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Float Switch
Detects the maximum water level to prevent overflow and potential flooding.
- Typical part-only price
- $15 - $40
- DIY difficulty
- Easy
- Estimated time
- 10-20 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 50W |
|---|---|
| component | Drain Pump |
| resistance | 10-20 ohms |
| part_number | HSDW-PUMP-001 |
| voltage_rating | 120V AC |
Common Questions
What does ED error mean on Hisense dishwasher?
ED error indicates a malfunction in the drain pump, causing the dishwasher to stop and fail to drain.
Can I fix Hisense dishwasher ED error myself?
Yes, perform a power reset and ensure the door is fully latched. Check for obstructions.
How much does it cost to fix ED error?
Repair costs for the ED error typically range from $50 to $200+, depending on parts needed.
When should I call a technician for ED?
Call a technician if the error persists after troubleshooting, or if you detect leaks or damage.
Sources & References
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!