Gorenje Dishwasher Error F67

⚡ Quick Answer: The Gorenje Dishwasher F67 error indicates a water supply issue, preventing the machine from detecting or receiving sufficient water for operation. Th... ✅ DIY Fixable

What Does Error F67 Mean?

The Gorenje Dishwasher F67 error indicates a water supply issue, preventing the machine from detecting or receiving sufficient water for operation. This error often leads to the dishwasher stopping shortly after starting and may be accompanied by unusual sounds. Common causes include insufficient water supply, blockages in the inlet hose or filters, or a malfunctioning water inlet valve.

Common Symptoms:

  • Dishwasher stops shortly after start with F67 displayed.
  • Insufficient water entering machine during fill phase.
  • No obvious water in tub yet error triggered.

Possible Causes

  • Insufficient water supply to the dishwasher (medium)
  • Potential blockage or kink in inlet hose or filters (medium)

How to Fix Error F67

DIY Fix Check basic water supply and inlet path

  1. Ensure the main water tap feeding the dishwasher is fully open.
  2. Inspect the dishwasher inlet hose for kinks or bends.
  3. Clean the inlet hose and machine-side screen/filter if accessible.

DIY Fix Perform a power reset

  1. Turn off the dishwasher and unplug it or remove its power via the breaker.
  2. Wait 5–10 minutes.
  3. Restore power and run a new cycle to see if the error reoccurs.

Technician Only Inspect and test water inlet valve and related components

  1. Disconnect power and water supply.
  2. Visually inspect the inlet valve, pressure sensor, and associated wiring.
  3. Test the inlet valve and pressure switch for continuity; replace if defective.
  4. Check filter screens and replace as needed.

Parts needed: Water inlet valve, Inlet hose, Pressure sensor, Filters

🛑 When to Call a Pro:
  • If the machine does not fill with water after basic checks and reset.
  • If inlet components are faulty or internal sensors/wiring show damage.
  • If error persists after user‑level troubleshooting.

Next step

Choose the next step for F67

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Water Inlet Valve

Controls the flow of hot and cold water into the appliance.

Typical part-only price
$25 - $60
DIY difficulty
Easy
Estimated time
15-30 mins
Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Technical Specifications

wattage 30W
component Drain Pump
resistance 10-20 ohms
part_number Gorenje 123456789
voltage_rating 230V AC

Common Questions

What does F67 error mean on Gorenje Dishwasher?

F67 indicates a water supply issue, causing the dishwasher to stop shortly after starting.

Can I fix Gorenje Dishwasher F67 error myself?

Yes, you can check the water supply, inspect the inlet hose, and reset the dishwasher.

How much does it cost to fix F67 error?

Estimated repair costs range from $50 to $200 depending on the specific issue.

When should I call a technician for F67?

Call a technician if the machine doesn't fill with water after your checks, or if the error persists.

Data last verified: 2026-04-23

User Comments (0)

Share your experience or solution below.

Be the first to comment!