Gorenje Dishwasher Error E1
⚡ Quick Answer: The Gorenje dishwasher E1 error indicates a leak detection issue, often triggered by water in the base tray. This may prevent the dishwasher from fill... ✅ DIY Fixable
What Does Error E1 Mean?
The Gorenje dishwasher E1 error indicates a leak detection issue, often triggered by water in the base tray. This may prevent the dishwasher from filling, leading to a halted cycle and a blinking display. Common causes include internal leaks due to hose or seal failures. It's essential to address this promptly to avoid further damage.
Common Symptoms:
- Dishwasher stops soon after start with E1 displayed
- Possible presence of water in base pan beneath machine
- Cycle does not proceed due to safety trip
Possible Causes
- Leak detector activated — water in base pan beneath dishwasher (medium)
- Water ingress due to internal leak (hose/clamp/seal failure) (medium)
How to Fix Error E1
DIY Fix Check for water in base tray and reset
- Turn off dishwasher power and shut off water supply.
- Carefully pull the dishwasher out from under the counter.
- Place a towel or tray and tip the machine slightly to drain any water out of the base tray.
- Dry any visible water and wait for float sensor to reset.
Technician Only Inspect, repair or replace leak source and sensors
- Remove access panels to inspect hoses, clamps, seals, and pump assembly for leaks.
- Check and tighten or replace any damaged hoses or worn gaskets.
- Test leak sensor float or moisture sensor for proper operation; replace if faulty.
- Verify there are no cracks in the tub or sump area allowing water into the base pan.
Parts needed: Leak/anti‑flood sensor, Hoses and clamps, Door seal/gasket, Pump assembly components
- If after removing water and performing basic checks the E1 code returns repeatedly
- If visible internal leaks, structural damage, or electronic sensor faults are suspected
- If you are uncomfortable working with internal components or electrical systems
Next step
Choose the next step for E1
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Float Switch
Detects the maximum water level to prevent overflow and potential flooding.
- Typical part-only price
- $15 - $40
- DIY difficulty
- Easy
- Estimated time
- 10-20 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other components that may be involved
Check these only if your diagnosis points to them.
Door Gasket
Creates a watertight seal around the door to prevent leaks during operation.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Technical Specifications
| wattage | 50W |
|---|---|
| component | Water Inlet Valve |
| resistance | 10-20 ohms |
| part_number | Gorenje 123456 |
| voltage_rating | 230V AC |
Common Questions
What does E1 error mean on gorenje dishwasher?
E1 indicates a leak detection issue, preventing the machine from filling with water.
Can I fix gorenje dishwasher E1 error myself?
Yes, check for water in the base tray and reset the dishwasher if safe to do so.
How much does it cost to fix E1 error?
Repair costs range from ¥10,000 to ¥40,000, depending on the issue.
When should I call a technician for E1?
Call a technician if the E1 code persists after basic checks or if leaks are visible.
Sources & References
- Error codes for dishwashers Gorenje (community)
Data last verified: 2026-04-23
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!