Viking Dishwasher: not stopping

Professional Repair Guide

What is this symptom?

Is your Viking dishwasher running continuously and not completing its cycle? This common issue can stem from a faulty control board or timer, preventing the appliance from stopping as it should. If you're experiencing this frustrating problem, it's essential to diagnose the cause quickly to avoid further complications.

Urgency: Medium

Important Tips for Viking Models

  • Viking documentation notes inconsistent cycle completion can be due to water inlet valve, timer or control board issues

Possible Causes

Faulty control board or timer causing continuous run signal

How to Identify: Cycle never advances or finishes; resetting power briefly halts but symptom resumes; control panel unresponsive to cycle completion.

Part: Control board / electronic timer

DIY Solutions

Power Reset to Clear Control Glitches

Easy 10-15 minutes
  1. Turn off dishwasher power at circuit breaker or unplug it.
  2. Wait 5–10 minutes to allow residual power to dissipate.
  3. Restore power and run a new cycle to test if it completes.
⚠️ Safety First: Ensure power is fully off before touching any dishwasher components.

Check and Test Door Latch/Switch

Moderate 30–45 minutes
Tools Needed: Screwdriver, Multimeter (optional)
  1. Turn off power to dishwasher.
  2. Open door and inspect latch for alignment and damage.
  3. Use multimeter to test switch continuity if comfortable.
  4. Replace latch or switch if defective.
  5. Restore power and test cycle.
⚠️ Safety First: Always disconnect power before accessing internal parts.

Inspect and Clean Float Switch

Moderate 20–30 minutes
Tools Needed: Screwdriver, Multimeter (optional)
  1. Remove bottom panel to access float assembly.
  2. Check float movement is free and not stuck by debris.
  3. Test switch for continuity.
  4. Clean around float or replace if defective.
  5. Reassemble and test dishwasher.
⚠️ Safety First: Disconnect power before working near electrical components.

Professional Repairs

Control Board/Timer Replacement

Estimated Cost: $200 - $450

Inlet Valve Replacement

Estimated Cost: $50 - $150

Drain/Flood Sensor and Pump Service

Estimated Cost: $100 - $250

When to Call a Professional

Dishwasher continues running after resets and DIY checks
Signs of water leakage or water in base pan
Multimeter testing suggests control board faults or failed major components

Preventive Maintenance

  • Clean float area and filters: Faulty water level detection and overflow conditions
    Frequency: monthly
  • Run basic maintenance cycle with vinegar: Debris buildup affecting sensors and valves
    Frequency: quarterly

Frequently Asked Questions

Why is my Viking Dishwasher not stopping?
The main causes include a faulty control board or timer sending a continuous run signal.
How do I fix Viking Dishwasher not stopping myself?
Try a power reset, check the door latch, or inspect the float switch for issues.
How much does it cost to fix not stopping?
Professional repairs typically range from $200 to $450 for control board replacement.
When should I call a technician for not stopping?
If DIY solutions fail or you're uncomfortable with electrical components, it's best to seek professional help.

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

50%
DIY Success Rate Difficulty: Either

Common Issues Reported by Users

  • Faulty door latch or door switch preventing the cycle from stopping
  • Water inlet valve stuck open, causing continuous filling
  • Malfunctioning control board or timer that fails to signal the end of the cycle

User Suggested Solutions

  1. Inspect the door latch and switch for damage or misalignment. Replace if necessary. Ensure the door is closing properly.

  2. Check the water inlet valve for proper operation. Disconnect power and water supply, then test the valve for continuity. Replace if faulty.

  3. Examine the control board for any visible signs of damage or burnt components. If necessary, replace the control board.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Viking dishwasher gurgling and won’t stop running

Community Discussions

gurgling and won’t stop running

The issue was likely due to a leak activating the flood mode.

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!