Simpson Washing Machine: making noise

Professional Repair Guide

What is this symptom?

Is your Simpson washing machine making unusual noises like rattling, grinding, or squealing? These sounds can occur during various cycles and often indicate issues such as an unbalanced load, foreign objects in the drum, or worn bearings. Understanding these noises can help you diagnose and fix the problem efficiently.

Urgency: Medium

Important Tips for Simpson Models

Simpson official support lists 'Unusual Noise' as a symptom category but does not provide detailed partâ€‘level troubleshooting steps publicly.
Simpson manuals emphasize checking pump filters and proper leveling to help reduce noise.

Possible Causes

Unbalanced load or improper load distribution

How to Identify: Loud thumping, banging, or vibration during spin, often eased by redistributing clothes.

Part: Drum/load distribution

Foreign objects in drum or pump

How to Identify: Clanking or rattling noise; objects like coins or bra wires seen when inspecting drum or pump filter.

Part: Drum interior / drain pump

Worn or damaged drum bearings

How to Identify: Grinding or rumbling noise during spin, excessive movement when manually pushing drum.

Part: Drum bearings

Faulty suspension/shock absorbers or suspension rods

How to Identify: Banging or excessive vibration during spin not fixed by load balancing or leveling.

Part: Shock absorbers / suspension rods

Worn or loose drive belt

How to Identify: Squealing or slapping noises, especially when motor runs; visible wear on belt.

Part: Drive belt

Clogged or faulty drain pump

How to Identify: Rattling or buzzing during drain cycle; debris seen in pump filter.

Part: Drain pump

DIY Solutions

Redistribute Laundry Load

Easy 2â€“5 minutes

Pause the wash cycle and open the door/lid.
Redistribute clothes evenly inside the drum to balance weight.
Restart the cycle and observe if noise decreases.

⚠️ Safety First: Ensure the machine is paused before opening.

Remove Foreign Objects

Moderate 10â€“20 minutes

Tools Needed: Flashlight, Screwdriver (if needed for access)

Unplug the machine before inspection.
Check inside drum for loose objects and remove them.
Locate and clean the drain pump filter (front bottom access on many models).
Remove any debris found and reassemble.
Plug in and test machine for noise reduction.

⚠️ Safety First: Disconnect power before reaching into filters or panels.

Professional Repairs

Replace Drum Bearings

Estimated Cost: $150 - $300

Replace Suspension/Shock Absorbers

Estimated Cost: $80 - $180

Replace Drive Belt

Estimated Cost: $30 - $80

Replace Drain Pump

Estimated Cost: $50 - $150

When to Call a Professional

Noise persists after basic DIY steps

Grinding or metal-on-metal sounds indicating internal wear

Excessive vibration or instability during spin

Visible leaks, burning smell, smoke

Preventive Maintenance

Balance loads properly: Unbalanced load noise and wear
Frequency: Every use
Clean drain pump filter: Debrisâ€‘related rattling and pump strain
Frequency: Monthly
Check and tighten accessible screws/feet: Loose component rattles
Frequency: Quarterly

Frequently Asked Questions

Why is my Simpson Washing Machine making noise?

Common causes include unbalanced loads, foreign objects in the drum, worn drum bearings, or faulty suspension.

How do I fix my Simpson Washing Machine making noise myself?

Try redistributing the laundry load or removing foreign objects from the drum and cleaning the drain pump filter.

How much does it cost to fix making noise?

Professional repairs can range from $30 for a drive belt to $300 for drum bearing replacement.

When should I call a technician for making noise?

If DIY solutions don't resolve the issue or if you suspect major component failures, it's best to consult a professional.

References & Sources

Simpson Support Washing Machine Troubleshooter Official

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

60%

DIY Success Rate Difficulty: Either

Common Issues Reported by Users

Worn or damaged drum bearings
Loose or damaged drive belt
Foreign objects trapped in the drum or pump

User Suggested Solutions

Inspect and replace worn drum bearings. Remove the back panel, take out the drum, and replace the bearings. Reassemble the machine.
Check the drive belt for looseness or damage. If loose, tighten it; if damaged, replace it. Ensure the belt is properly aligned.
Examine the drum and pump for foreign objects. Remove any items found and check for any blockages in the pump.