Roper Washing Machine: not filling with water, not spinning
What is this symptom?
If your Roper washing machine is not filling with water and failing to spin, it could leave your clothes soaking wet. This issue may be caused by a closed water supply, clogged hoses, or a faulty lid switch. Understanding these common problems can help you troubleshoot the situation effectively.
Important Tips for Roper Models
- Some Roper washers may include a plastic tube attached to the water level valve that can clog and affect water fill
Possible Causes
Closed or insufficient water supply
How to Identify: Hot/cold faucets behind washer may be partially or fully off; low household water pressure affects flow.
Part: Water supply valves / house water pressure
Clogged or kinked inlet hoses and filters
How to Identify: Hoses bent or blocked; small mesh filters at hose connections clogged with debris.
Part: Inlet hoses and mesh filters
Faulty water inlet valve
How to Identify: Washer hums but no water enters; intermittent or no fill even with good water pressure.
Part: Water inlet valve
Pressure switch or level control issues
How to Identify: Machine may think it’s full prematurely or won’t register fill; pressure hose blocked or disconnected.
Part: Pressure switch / pressure hose
Faulty lid switch or spin safety interlock
How to Identify: Machine won’t spin; spin starts if lid switch bypassed or not engaging properly.
Part: Lid switch / door latch
Drive belt / motor coupling wear or failure
How to Identify: No spin despite proper load; audible motor but drum doesn’t turn.
Part: Drive belt, motor coupling
DIY Solutions
Check and open water supply valves
- Locate hot and cold water valves behind the washer
- Ensure both are fully turned on (counter-clockwise)
- Run a short cycle to test fill
Clean inlet hoses and mesh filters
- Turn off water supply and unplug washer
- Disconnect inlet hoses from washer
- Remove and rinse mesh filters at hose ends
- Reattach hoses and restore water supply
Test and replace lid switch
- Unplug washer and access lid switch area
- Test switch continuity with multimeter
- Replace switch if no continuity
Redistribute laundry load before spin
- Open washer and redistribute clothes evenly in drum
- Remove some items if overloaded
- Restart spin cycle
Next step
Choose the next step for not filling with water, not spinning
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
- Typical part-only price
- $25 - $60
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Pressure Switch
Detects the water level inside the tub and signals when to start or stop filling.
Door Latch Assembly
Mechanically secures the appliance door and may operate a door-closed safety switch.
Door or Lid Switch
Detects whether the appliance door or lid is safely closed before operation.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace water inlet valve
Replace pressure switch or level control
Inspect and replace drive belt/motor coupling
Drain pump inspection and repair
Control board diagnosis or replacement
When to Call a Professional
Preventive Maintenance
-
Clean inlet hose filters: Clogged water inlet and fill problems
Frequency: annually -
Balance loads evenly: Spin cycle interruptions due to imbalance
Frequency: Every wash
Frequently Asked Questions
Why is my Roper Washing Machine not filling with water, not spinning?
How do I fix Roper Washing Machine not filling with water, not spinning myself?
How much does it cost to fix not filling with water, not spinning?
When should I call a technician for not filling with water, not spinning?
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Clogged water inlet valve or hoses
- Faulty lid switch preventing operation
- Broken drive coupler affecting spinning
User Suggested Solutions
-
Check and clean the water inlet valve and hoses. Ensure that the hoses are not kinked or clogged. Turn off the water supply, disconnect the hoses, and flush them out. Replace the inlet valve if necessary.
-
Inspect the lid switch for continuity using a multimeter. If the switch is defective, replace it to restore functionality. Ensure the lid is properly closed during operation.
-
Check the drive coupler between the motor and the transmission. If it is broken, replace it. This involves removing the cabinet and accessing the motor area.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
makes a light humming noise, no water fills the machine, and the machine doesn't spin
Check water valves and hoses; if humming, check lid switch and coupler.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!