Miele Washing Machine: shaking during spin cycle

Professional Repair Guide

What is this symptom?

Is your Miele washing machine shaking excessively during the spin cycle? This common issue can lead to noise and instability, often caused by an unbalanced load, improper leveling, or residual shipping bolts. Understanding the root cause is essential for effective troubleshooting and repair.

Urgency: Medium

Important Tips for Miele Models

  • Miele explicitly requires removal of transport bolts and strict leveling procedures; unstable floors (e.g., wood) can aggravate vibration issues.

Possible Causes

Uneven or unbalanced laundry load

How to Identify: Shaking occurs only with certain loads, especially mixed heavy and light items or very small loads.

Part: Drum/load distribution

Incorrect leveling or placement of the washer

How to Identify: Machine rocks when pressed at the top corners; not level on a spirit level; feet counter‑nuts loose.

Part: Adjustable leveling feet/floor surface

Transport shipping bolts not removed

How to Identify: Occurs on new machines or after a move; bolts still present at back of washer.

Part: Transport bolts

Worn or damaged shock absorbers/suspension springs

How to Identify: Persistent severe shaking even with balanced load and level surface; noise when spinning; inspection shows worn dampers/springs.

Part: Shock absorbers/Suspension springs

Loose or damaged counterweights

How to Identify: Heavy knocking or thumping during spin; washer shakes violently and evenly distributed loads still vibrate.

Part: Counterweights

DIY Solutions

Redistribute Laundry Load

Easy 2-5 minutes
  1. Open drum and redistribute clothes evenly around the drum circumference.
  2. Ensure a mix of heavy and light items is balanced; avoid single large items alone.
  3. Run a short spin cycle to test vibration reduction.

Level the Washing Machine

Moderate 10-20 minutes
Tools Needed: Spirit level, Adjustable wrench or pliers
  1. Check machine level with a spirit level across front and side.
  2. Adjust each foot to achieve level position.
  3. Tighten counter nuts against housing to lock feet in position.
  4. Test with a spin cycle.
⚠️ Safety First: Ensure power is off when moving the machine to adjust feet.

Remove Transport Shipping Bolts

Moderate 10-15 minutes
Tools Needed: Wrench/hex key (usually supplied)
  1. Locate shipping bolts at rear of machine (typically four).
  2. Use correct tool to unscrew and remove all bolts.
  3. Store bolts in a safe place for future transport.
  4. Place machine back and level it, then test spin.
⚠️ Safety First: Disconnect power before removing bolts.

Next step

Choose the next step for shaking during spin cycle

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Check during diagnosis

Most relevant component to inspect

Washer Shock Absorber

Dampens tub movement and vibration during high-speed spin cycles.

Typical part-only price
$25 - $100
DIY difficulty
Medium
Estimated time
45-90 mins
Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Model number required

Model-compatible Washing Machine parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Washing Machine Cleaner Tablets

Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.

View maintenance supply
Maintenance supply

Braided Washer Inlet Hoses

A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.

View maintenance supply
Maintenance supply

Washer Drain Hose Holder

Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace Shock Absorbers or Suspension Springs

Estimated Cost: $80 - $250

Inspect and Secure Counterweights

Estimated Cost: $100 - $300

When to Call a Professional

Persistent violent shaking despite balanced load and correct leveling
Strange noises suggest bearings, damper or counterweight issues
Visible leaks or electrical faults during spin cycle

Preventive Maintenance

  • Check leveling regularly: Uneven vibration and excessive wear
    Frequency: Every 6 months
  • Avoid unbalanced loads: Spin cycle imbalance and vibration issues
    Frequency: Every wash

Frequently Asked Questions

Why is my Miele Washing Machine shaking during spin cycle?
Common causes include uneven laundry loads, incorrect leveling, and shipping bolts not removed.
How do I fix Miele Washing Machine shaking during spin cycle myself?
Redistribute laundry evenly, level the washer, or remove transport shipping bolts.
How much does it cost to fix shaking during spin cycle?
Professional repairs range from $80 to $300 depending on the issue.
When should I call a technician for shaking during spin cycle?
If DIY solutions don't resolve the issue or if you suspect damaged parts.

References & Sources

Community Analytical Insights

Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions

Common Issues Reported by Users

  • Unbalanced load due to uneven distribution of laundry
  • Worn shock absorbers that fail to dampen vibrations
  • Damaged or worn bearings affecting drum stability
  • Broken spider arm causing drum misalignment
  • Improper installation or leveling of the washing machine

User Suggested Solutions

  1. Check and redistribute the load in the drum. Remove excess items and ensure a balanced load before restarting the spin cycle.

  2. Inspect the shock absorbers for wear or damage. Replace if necessary by removing the outer casing and unscrewing the old parts.

  3. Check the bearings for wear. If they are noisy or feel rough, they need to be replaced. This may require disassembling the drum.

  4. Examine the spider arm for any breaks or misalignment. If damaged, it will need to be replaced, which can be complex.

  5. Ensure the washing machine is level by adjusting the feet. Use a spirit level to check and make adjustments as needed.

Limited-source guidance; percentages and success-rate claims are not shown
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Miele w750 violently shaking after loud noise

Community Discussions

violently shaking after loud noise during spin cycle

Check for unbalanced loads, broken shock absorbers, worn-out bearings, or a broken spider.

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!

Call Local Repair Provider +1 (888) 217-6318