Miele Washing Machine: excessive movement during spin cycle

Professional Repair Guide

What is this symptom?

Experiencing excessive movement or vibration from your Miele washing machine during the spin cycle? This common issue often results in the washer shifting position, especially at high speeds. Improper installation or load distribution can contribute to this problem, making it essential to address it promptly for optimal performance.

Urgency: Medium

Important Tips for Miele Models

  • Miele specifically lists transport safety device left in place and incorrect leveling as primary causes of vibration during spin cycle.

Possible Causes

Transport bolts/safety devices still installed

How to Identify: Machine vibrates violently only during first uses after installation; transport bolts still visible on rear of the washer.

Part: Transport safety bolts

DIY Solutions

Remove transport safety bolts

Easy 5-10 minutes
Tools Needed: wrench/spanner
  1. Locate transport safety bolts on rear of the washer (present from delivery).
  2. Use an appropriate wrench to remove all transport bolts.
  3. Store bolts for future transportation.
⚠️ Safety First: Ensure machine is unplugged when accessing rear panel.

Level and secure washer feet

Moderate 10-20 minutes
Tools Needed: spirit level, wrench
  1. Place a spirit level on top of the machine to check for level in all directions.
  2. Adjust each leg by turning the adjustable feet until the machine is level.
  3. Tighten the counter nuts against the base housing to lock feet in place.
⚠️ Safety First: Be cautious while adjusting to avoid pinching fingers.

Redistribute laundry load

Easy 2-3 minutes
  1. Pause wash cycle and open door once safe.
  2. Evenly distribute laundry inside the drum, avoiding bulky items alone.
  3. Restart spin cycle.
⚠️ Safety First: Ensure cycle is safe to open before pausing.

Professional Repairs

Replace worn shock absorbers/dampers

Estimated Cost: $80 - $200 (parts) plus labor

When to Call a Professional

Vibration persists after removing transport bolts and correct leveling.
Suspicion of internal component wear (shock absorbers) or unusual noises from drum.
Damage to floor or machine caused by vibration.

Preventive Maintenance

  • Check and re‑level washer feet: Excessive vibration and movement during spin
    Frequency: annually or after relocation
  • Inspect shock absorbers after ~5‑7 years of use: Internal wear leading to vibration issues
    Frequency: as needed based on vibration levels

Frequently Asked Questions

Why is my Miele Washing Machine excessive movement during spin cycle?
The excessive movement is often due to transport bolts still being installed or an unbalanced load.
How do I fix Miele Washing Machine excessive movement during spin cycle myself?
Remove transport bolts, level the washer feet, and redistribute the laundry load for a stable spin.
How much does it cost to fix excessive movement during spin cycle?
Professional repairs to replace worn shock absorbers cost between $80 - $200, plus labor.
When should I call a technician for excessive movement during spin cycle?
Call a technician if DIY solutions don't resolve the issue or if you suspect worn parts.

References & Sources

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

80%
DIY Success Rate Difficulty: DIY

Common Issues Reported by Users

  • Unlevel installation causing imbalance during spin
  • Worn or damaged shock absorbers affecting stability
  • Overloading the drum beyond its capacity leading to excessive movement

User Suggested Solutions

  1. Ensure the washing machine is level by adjusting the feet. Use a level tool to check and make necessary adjustments. Adding rubber pads can also help stabilize the machine.

  2. Inspect and replace worn shock absorbers. Open the back panel, locate the shock absorbers, and replace them if they show signs of wear or damage.

  3. Reduce the load size in the drum. Check the manufacturer's guidelines for load capacity and adjust the amount of laundry accordingly.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Any advice on dealing with a front-load washing machine that...

Community Discussions

moves around a bit during the spin cycle

Adjusted leveling and added rubber pads to stabilize the machine.

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!