LG Washing Machine: loud noise during spin cycle

Possible Causes

Unbalanced laundry load

How to Identify: Noise occurs when heavy items clump on one side; thumping or banging sound, often intermittent.

Part: Drum/internal load

Washer not level or improperly installed

How to Identify: Machine vibrates loudly and rocks on the floor when spinning; visual tilt.

Part: Washer feet/installation

Foreign objects trapped in drum or pump

How to Identify: Rattling, metallic scraping/noise possible; objects visible in drum holes or removed from pump filter.

Part: Drum interior/pump

Worn or damaged drum bearings

How to Identify: Consistent grinding or high‑pitch noise at high spin speeds; noise persists despite balanced load.

Part: Tub bearings

Damaged or loose drive belt/pulley

How to Identify: Squeaking or squealing or irregular noise from belt area during spin; visible wear on belt.

Part: Drive belt/drive pulley

DIY Solutions

Redistribute laundry for balance

Easy 2–5 minutes

1. Open washer and lift heavy items from one side.
2. Rearrange and evenly distribute clothes around drum.
3. Run spin cycle again to check if noise reduced.

Level the washing machine

Moderate 10–15 minutes

Tools Needed: Level tool, Wrench or pliers

1. Place level on top of washer to check balance.
2. Adjust feet up or down until machine is level.
3. Tighten lock nuts and re‑run spin cycle.

⚠️ Safety First: Ensure machine is unplugged when adjusting feet

Remove foreign objects from drum/pump

Moderate 15–30 minutes

Tools Needed: Flashlight, Screwdriver

1. Check drum holes and interior for coins or small objects.
2. Remove front panel if needed and inspect pump/filter area.
3. Clear out any debris and replace panels.
4. Re‑test spin cycle.

⚠️ Safety First: Disconnect power before accessing internal areas

Next step

Choose the next step for loud noise during spin cycle

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Drum Bearing Kit

Supports the spinning drum and ensures smooth, quiet rotation during cycles.

Typical part-only price

$40 - $95

DIY difficulty

Hard

Estimated time

120-180 mins

Optional: enter your model number

Apply

Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Possible related component

Drive Belt

Transfers rotational power from the motor to turn the drum or tub.

$15 - $35 · Easy · 20-30 mins

Check fit & price

Model number required

Model-compatible Washing Machine parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Washing Machine Cleaner Tablets

Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.

View maintenance supply

Maintenance supply

Braided Washer Inlet Hoses

A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.

View maintenance supply

Maintenance supply

Washer Drain Hose Holder

Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace worn tub bearings

Estimated Cost: $150–$300+

Replace drive belt or pulley

Estimated Cost: $50–$150

When to Call a Professional

If loud grinding noise persists after load redistribution and leveling

If noise continues after removing foreign objects

If bearings or internal components are suspected damaged

Preventive Maintenance

• Check and balance loads each time: Unbalanced load noise and vibration
  Frequency: Every use
• Periodically check and clean pump filter: Noise from trapped debris
  Frequency: Every 3–6 months

Frequently Asked Questions

Why is my LG Washing Machine loud noise during spin cycle?

Common causes include unbalanced loads, improper leveling, or foreign objects in the drum.

How do I fix LG Washing Machine loud noise during spin cycle myself?

Redistribute laundry for balance, level the washer, or check for foreign objects in the drum.

How much does it cost to fix loud noise during spin cycle?

Professional repairs can range from $50 for a drive belt to $300 for replacing worn tub bearings.

When should I call a technician for loud noise during spin cycle?

If DIY fixes don’t resolve the issue, or if you suspect serious damage, contact a technician.

References & Sources

• LG top load washing machine noise during spin Official
• LG front load washer noise at end of spin Official
• 4 Reasons Your LG Washer Is Loud During Spin Cycle Community
• Troubleshooting an LG washer loud during spin Repair-Blog

Common Issues Reported by Users

• Worn central bearings (1 mentions)
• Faulty agitator (1 mentions)

User Suggested Solutions