LG Washing Machine: broken stator and damaged wiring
What is this symptom?
Experiencing issues with your LG washing machine? A broken stator and damaged wiring can cause no spin or agitation, buzzing sounds, and error codes like LE. Inspect the rear panel for visible damage and ensure your washer functions properly again.
Important Tips for LG Models
- LG Direct Drive washers can suffer broken motor wire harness or position sensor wire causing motor control issues.
Possible Causes
Stator winding failure (burnt or open coils)
How to Identify: Visual inspection may show burn marks or broken coils; multimeter resistance outside expected range indicates fault. Symptoms include washer not spinning or agitating and motor error codes.
Part: Stator assembly (direct drive motor stator)
Damaged motor wiring harness or chafed wires
How to Identify: Visible frayed, melted, or broken wires in harness to stator or RPS sensor; intermittent electrical communication issues; washer may not start or show motor-related errors.
Part: Motor wiring harness / connectors
Rotor position sensor failure (adjacent to stator)
How to Identify: Buzzing, jerking motion of rotor, locked rotor conditions; error codes persisting after stator inspection.
Part: Rotor position sensor
DIY Solutions
Test and Replace Stator Assembly
- Unplug washer and turn off water supply.
- Remove rear access panel to expose motor assembly.
- Use multimeter to test stator winding resistance across all coil pairs.
- If windings are open or out of range, unbolt and disconnect old stator.
- Install new stator and reconnect harness, observing correct orientation.
- Reassemble rotor and access panel, reconnect hoses and power.
- Run a test cycle to check spin and listen for unusual noises.
Inspect and Repair/Replace Damaged Wiring Harness
- Unplug washer and remove back panel.
- Visually inspect motor wiring harness for frayed, broken, or melted wires.
- Use multimeter to check continuity of suspect wires.
- Cut out damaged section and splice in new wire with appropriate connectors and insulation.
- Secure harness away from vibration points to prevent future chafing.
- Reassemble and test machine operation.
Next step
Choose the next step for broken stator and damaged wiring
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drive Motor
Drives the drum, agitator, or pump to rotate during cycles.
- Typical part-only price
- $90 - $220
- DIY difficulty
- Hard
- Estimated time
- 45-90 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
OEM Stator Replacement by Technician
Motor Wiring Harness and RPS Sensor Replacement
When to Call a Professional
Preventive Maintenance
-
Inspect motor wiring harness routing: Chafing and insulation wear leading to wiring damage.
Frequency: annually -
Clean and inspect rear motor area for moisture: Corrosion or moisture-related electrical faults.
Frequency: every 6 months
Frequently Asked Questions
Why is my LG Washing Machine broken stator and damaged wiring?
How do I fix LG Washing Machine broken stator and damaged wiring myself?
How much does it cost to fix broken stator and damaged wiring?
When should I call a technician for broken stator and damaged wiring?
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Worn or broken stator due to age and excessive use
- Damaged wiring from exposure to moisture or physical abrasion
- Faulty bearings causing excessive vibration, leading to stator damage
User Suggested Solutions
-
Inspect the wiring for visible damage, replace any damaged sections, and ensure all connections are secure. If the stator is broken, remove the old stator and install a new one following the manufacturer's guidelines.
-
Test the motor with a multimeter to check for continuity. If the stator is faulty, replace it with a compatible part. Ensure to check bearings and replace if necessary.
-
Consult the user manual for troubleshooting steps specific to your model. If issues persist after basic checks, consider professional diagnostics.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!