Hotpoint Washing Machine: noisy during spin

Professional Repair Guide

What is this symptom?

Is your Hotpoint washing machine making loud noises during the spin cycle? You may be experiencing rumbling, grinding, or banging sounds, especially at high speeds. This could indicate issues like worn drum bearings, an unbalanced load, or faulty shock absorbers. Identifying the cause early can help prevent further damage.

Urgency: Medium

Important Tips for Hotpoint Models

  • Worn drum bearings and tub seal assemblies are frequently documented causes of loud spin noise on Hotpoint washers.
  • Shipping bolts left in after installation can cause significant spin noise on new Hotpoint washers if not removed.

Possible Causes

Worn or failed drum bearings

How to Identify: Loud rumbling or grinding noise that worsens over time during spin; noise persists regardless of load balance

Part: drum bearings / tub seal and bearing kit

Unbalanced or uneven laundry load

How to Identify: Noise mostly when spin starts or while spinning, reduces when rebalancing load; heavy items grouped on one side

Part: wash load distribution

Faulty or worn suspension/shock absorbers

How to Identify: Excessive vibration and noise during spin, machine ‘walks’ or rocks more than usual

Part: suspension rods/shock absorbers

Transport/shipping bolts not removed

How to Identify: New installation and loud noise first spins; bolts still present at rear of washer

Part: shipping bolts

Foreign objects in drum or between tub and outer tub

How to Identify: Rattling or clattering noise, sometimes correlated with objects like coins or hard items

Part: drum interior/space between inner and outer tub

Loose internal parts (e.g., drum screws, spider arm)

How to Identify: Intermittent loud bangs or metal-on-metal noise; might be louder only at specific spin speeds

Part: drum screws/spider arm

DIY Solutions

Rebalance Laundry Load

Easy 5-10 minutes
  1. Stop machine and open door
  2. Redistribute clothes evenly around the drum
  3. Avoid overly heavy items alone; run again
⚠️ Safety First: Do not open door mid-spin if locked

Remove Foreign Objects from Drum

Moderate 10-20 minutes
Tools Needed: Flashlight
  1. Stop machine and unplug
  2. Inspect drum interior and gasket area for coins or hard objects
  3. Remove any objects found
  4. Run a short spin to test
⚠️ Safety First: Unplug before inspecting

Check and Adjust Shipping Bolts (New Install)

Moderate 10-20 minutes
Tools Needed: Wrench/socket set
  1. Unplug and pull machine away from wall
  2. Check rear for shipping bolts
  3. Remove bolts per manual
  4. Store bolts safely
  5. Level machine and test spin
⚠️ Safety First: Follow manual instructions

Next step

Choose the next step for noisy during spin

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Check during diagnosis

Most relevant component to inspect

Drum Bearing Kit

Supports the spinning drum and ensures smooth, quiet rotation during cycles.

Typical part-only price
$40 - $95
DIY difficulty
Hard
Estimated time
120-180 mins
Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Possible related component

Washer Shock Absorber

Dampens tub movement and vibration during high-speed spin cycles.

$25 - $100 · Medium · 45-90 mins

Check fit & price
Possible related component

Washer Suspension Rod Kit

Supports and stabilizes the washer tub during agitation and spin.

$35 - $120 · Medium · 45-90 mins

Check fit & price
Model number required

Model-compatible Washing Machine parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Washing Machine Cleaner Tablets

Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.

View maintenance supply
Maintenance supply

Braided Washer Inlet Hoses

A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.

View maintenance supply
Maintenance supply

Washer Drain Hose Holder

Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace Drum Bearings/Tub Seal

Estimated Cost: $150 - $350

Replace Suspension/Shock Absorbers

Estimated Cost: $80 - $200

Internal Drum Hardware Tightening/Repair

Estimated Cost: $100 - $250

When to Call a Professional

Noise persists after rebalancing and basic checks
Loud metal-on-metal grinding or rumbling
Water leaking near base or under machine
Unusual vibrations causing machine movement
Noise occurs regardless of load distribution

Preventive Maintenance

  • Ensure load balance every wash: Imbalance-caused vibration/noise
    Frequency: Each use
  • Level machine with adjustable feet: Excessive vibration and noise
    Frequency: monthly check
  • Inspect and clean drum interior for objects: Noise from foreign objects
    Frequency: monthly

Frequently Asked Questions

Why is my Hotpoint Washing Machine noisy during spin?
Common causes include worn drum bearings, unbalanced loads, or faulty shock absorbers.
How do I fix Hotpoint Washing Machine noisy during spin myself?
Try redistributing the laundry load evenly or check for foreign objects in the drum.
How much does it cost to fix noisy during spin?
Professional repairs range from $80 to $350 depending on the issue.
When should I call a technician for noisy during spin?
If DIY solutions don't resolve the issue, or if the noise persists, call a technician.

Community Analytical Insights

Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions

Common Issues Reported by Users

  • Loose or improperly tightened bolts on the drum or concrete block
  • Worn out or damaged bearings
  • Unbalanced load or overloaded drum

User Suggested Solutions

  1. Check and tighten all bolts securing the drum and concrete block. Ensure the washing machine is level by adjusting the feet. Run a spin cycle to test for noise.

  2. Inspect the bearings for wear or damage. If they are worn, replace them by disassembling the drum. This may require specialized tools.

  3. Redistribute the load in the drum to ensure it is balanced. Avoid overloading the machine. Run a spin cycle to check for noise reduction.

Limited-source guidance; percentages and success-rate claims are not shown
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Hotpoint washing machine extremely noisy during spin

Community Discussions

extremely noisy during spin

One of the bolts holding the concrete block hadn't been properly tightened when it was refitted. The machine was also leveled better.

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!

Call Local Repair Provider +1 (888) 217-6318