Hoover Washer Dryer: filling with water
What is this symptom?
Is your Hoover Washer Dryer unexpectedly filling with water during cycles or while drying? This can be caused by a faulty water inlet valve, blocked hoses, or incorrect drain setup. Understanding the root of the problem can help you resolve it efficiently.
Important Tips for Hoover Models
- Hoover washer dryers may briefly fill with water at the start of a drying programme as part of normal operation.
Possible Causes
Normal brief fill at start of drying cycle
How to Identify: Water briefly enters through the detergent dispenser at the start of drying program; not continuous filling
Part: water inlet system
Faulty or stuck open water inlet valve
How to Identify: Water continues to flow into drum when machine is off or beyond fill stage; shutting off water supply stops fill
Part: water inlet valve
Blocked or kinked inlet hoses / filters
How to Identify: Poor water flow or irregular filling behaviour; kinks visible in hose or debris in screens
Part: inlet hoses and filter screens
Drain hose siphoning / incorrect drain setup
How to Identify: Water appears to fill but actually siphon due to drain hose positioned too low or incorrectly installed
Part: drain hose / connection
Pump or condenser blockage (specific to washer-dryer drying mode)
How to Identify: Excessive water accumulation during drying cycle beyond expected brief fill
Part: pump, condenser system
DIY Solutions
Check if the brief fill during drying is normal
- Run a dry cycle and observe if the water fill is only momentary at the start.
- If it stops quickly and programme continues, this is expected behaviour per Hoover advice.
Inspect and clean inlet hose filters
- Turn off water supply to the washer dryer.
- Disconnect inlet hoses from the back of the machine.
- Remove and rinse the filter screens in the hoses and at the inlet valve.
- Reattach hoses securely and turn water supply back on.
Verify drain hose position to prevent siphoning
- Ensure the drain hose is installed at correct height and not pushed too far into standpipe.
- Straighten any kinks in drain hose and secure with proper brackets.
Next step
Choose the next step for filling with water
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
- Typical part-only price
- $25 - $60
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
Model-compatible Washer Dryer parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dryer Vent Cleaning Kit
Helps remove routine lint buildup from an accessible dryer vent path. It does not diagnose or repair an E-code or failed component.
Lint Trap Cleaning Brush
A narrow brush for routine cleaning around an accessible lint screen and housing.
Dryer Vent Hose Kit
A replacement exhaust duct option for visibly crushed or damaged external venting. Check diameter, length, local code, and installation clearance.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace water inlet valve
Inspect and service condenser or drain pump
When to Call a Professional
Preventive Maintenance
-
Clean inlet filters: Blockage and improper water fill behaviour
Frequency: every 3 months -
Check drain hose positioning: Siphoning and unintended water flow issues
Frequency: annually
Frequently Asked Questions
Why is my Hoover Washer Dryer filling with water?
How do I fix Hoover Washer Dryer filling with water myself?
How much does it cost to fix filling with water?
When should I call a technician for filling with water?
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Faulty water inlet valve allowing water to flow even when the machine is off
- Clogged or kinked hose preventing proper drainage, leading to backflow
- Defective pressure switch not detecting water level correctly
User Suggested Solutions
-
Inspect and replace the water inlet valve. Turn off the water supply, disconnect the hoses, remove the valve, and install a new one. Reconnect hoses and turn on the water supply.
-
Check and clear any clogs in the hoses. Disconnect the hoses from both the washer and the water supply, and clean them thoroughly. Ensure they are not kinked when reattached.
-
Test and replace the pressure switch if necessary. Access the switch, check for continuity with a multimeter, and replace it if it fails the test.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
filling while turned off
Filling valve may be letting by; consider getting a technician out under warranty.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!