Fisher & Paykel Dishwasher: error code F2

Professional Repair Guide

What is this symptom?

If your Fisher & Paykel Dishwasher displays error code F2, you may experience interruptions in the wash cycle, beeping sounds, and issues with washing or draining. This error typically indicates a problem with the wash motor, which may be stalled or failed, or could be caused by an obstruction in the pump area or loose wiring. Identifying and addressing these issues can restore your dishwasher's functionality.

Urgency: Medium

Important Tips for Fisher & Paykel Models

  • Official fault code documentation lists F2 as a motor rotor fault requiring service if basic reset fails.

Possible Causes

Wash motor fault (motor rotor stalled or failed)

How to Identify: F2 code appears; dishwasher stops mid‑cycle or won’t start wash pump; inspection shows impeller won’t spin or is obstructed.

Part: Wash motor / motor rotor

Obstruction in wash pump or impeller area

How to Identify: Debris (e.g., broken glass, food particles visible under spray arm or around pump rotor; rotor won’t spin freely by hand.

Part: Wash pump impeller / sump area

Loose or damaged wiring to wash motor

How to Identify: Intermittent operation; visual inspection shows loose connectors or damaged wires near motor.

Part: Motor wiring harness / connectors

DIY Solutions

Clear Obstructions at Wash Pump and Impeller

Moderate 30–60 minutes
Tools Needed: screwdriver, flashlight, protective gloves
  1. Turn off and disconnect power supply
  2. Open dishwasher, remove racks and spray arm
  3. Inspect bottom sump area for debris; remove any found
  4. Access pump area if needed and ensure rotor can spin freely
  5. Reassemble and restore power; test run
⚠️ Safety First: Disconnect electrical power before servicing

Soft Reset the Dishwasher

Easy 5 minutes
  1. Turn off dishwasher at power or breaker
  2. Wait 30–60 seconds
  3. Restore power and start a short cycle

Next step

Choose the next step for error code F2

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Dishwasher Circulation Pump

Circulates pressurized water through the dishwasher spray arms during the wash cycle.

Typical part-only price
$90 - $220
DIY difficulty
Hard
Estimated time
60-120 mins
Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Professional Repairs

Replace Wash Motor or Motor Rotor

Estimated Cost: $150 - $400

Inspect and Repair Wiring or Control Signals

Estimated Cost: $100 - $300

When to Call a Professional

Motor does not run after clearing debris and reset
Visual damage or seized motor components
Persistent F2 code after DIY steps
Uncomfortable performing internal electrical component checks

Preventive Maintenance

  • Clean filters and sump area: Debris buildup that can obstruct the wash motor or impeller and lead to F2
    Frequency: monthly
  • Check spray arms and remove trapped food debris: Blockages that can stress the wash pump and motor
    Frequency: monthly

Frequently Asked Questions

Why is my Fisher & Paykel Dishwasher error code F2?
Error code F2 can be caused by a wash motor fault, obstruction in the wash pump, or loose wiring.
How do I fix Fisher & Paykel Dishwasher error code F2 myself?
You can clear obstructions in the wash pump or perform a soft reset to attempt a fix.
How much does it cost to fix error code F2?
Professional repair costs for error code F2 range from $100 to $400, depending on the issue.
When should I call a technician for error code F2?
If DIY fixes don't work or if you're unsure, it's best to call a technician due to the medium urgency.

References & Sources

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

70%
DIY Success Rate Difficulty: Either

Common Issues Reported by Users

  • Blocked drain or filter causing water to back up
  • Faulty pressure switch not detecting water levels correctly
  • Stuck motor rotors or pump issues preventing water circulation

User Suggested Solutions

  1. Check and clean the drain filter and drain hose. Remove any debris that may be blocking the water flow. Ensure the drain hose is not kinked or clogged.

  2. Inspect the pressure switch for any signs of damage or blockage. If necessary, replace the pressure switch to ensure accurate water level detection.

  3. Examine the motor rotors for any obstructions or damage. If the rotors are stuck, attempt to free them. If damaged, replace the motor assembly.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. F2 error on Fisher & Paykel DD603 24in

Community Discussions

F2 error

The motor rotors are stuck and need to be replaced.

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!