Electrolux Washer Dryer: error codes

Possible Causes

Water inlet issue (e.g., insufficient water supply)

How to Identify: Error code E10 or similar appears during initial fill; water fills slowly or not at all.

Part: Water inlet valve / supply hose

Drainage blockage or pump issue

How to Identify: Error code E20/E21/C2 appears; washer not draining; water remains in drum.

Part: Drain pump / hose

Door lock or hatch detection fault

How to Identify: Error codes like E40/E41 (door appear; machine won’t start or pauses mid-cycle.

Part: Door lock switch / sensor

Water pressure sensor / level issue

How to Identify: Error code E30 or similar; abnormal water level behavior.

Part: Pressure sensor / water level switch

Motor or drive control faults

How to Identify: Codes related to motor (various E4x appear; agitation/spin issues.

Part: Motor control board / tachometer sensor

DIY Solutions

Check and clear drain filter and hose

Moderate 20-30 minutes

Tools Needed: screwdriver, bucket, towel

1. Turn off and unplug the washer dryer.
2. Locate and remove the drain filter access panel.
3. Unscrew and clean the filter; remove debris.
4. Check the drain hose for kinks or blockages; clear if needed.
5. Reinstall filter and run a rinse cycle to test.

⚠️ Safety First: Disconnect power before opening panels.

Ensure door is fully closed and latch engaged

Easy 5 minutes

1. Open and firmly close the washer door.
2. Listen for the latch click; ensure nothing obstructs closure.
3. Restart machine to see if error clears.

Inspect water supply hoses and inlet screens

Moderate 15-25 minutes

Tools Needed: adjustable wrench, bucket

1. Turn off water supply and power.
2. Disconnect inlet hoses; check for blockages in screens.
3. Clean screens and reconnect hoses securely.
4. Turn water back on and test for filling.

Next step

Choose the next step for error codes

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Water Inlet Valve

Controls the flow of hot and cold water into the appliance.

Typical part-only price

$25 - $60

DIY difficulty

Easy

Estimated time

15-30 mins

Optional: enter your model number

Apply

Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Possible related component

Drain Pump

Pumps waste water out of the appliance during the drain cycle.

$35 - $80 · Easy · 15-30 mins

Check fit & price

Possible related component

Door Lock Assembly

Secures the door shut during operation for safety and signals the control board to run.

$30 - $75 · Easy · 10-20 mins

Check fit & price

Possible related component

Pressure Switch

Detects the water level inside the tub and signals when to start or stop filling.

$25 - $65 · Easy · 15-30 mins

Check fit & price

Model number required

Model-compatible Washer Dryer parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Dryer Vent Cleaning Kit

Helps remove routine lint buildup from an accessible dryer vent path. It does not diagnose or repair an E-code or failed component.

View maintenance supply

Maintenance supply

Lint Trap Cleaning Brush

A narrow brush for routine cleaning around an accessible lint screen and housing.

View maintenance supply

Maintenance supply

Dryer Vent Hose Kit

A replacement exhaust duct option for visibly crushed or damaged external venting. Check diameter, length, local code, and installation clearance.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace faulty drain pump or motor assembly

Estimated Cost: $80 - $250

Replace door lock/sensor assembly

Estimated Cost: $50 - $150

Service control board/electronics

Estimated Cost: $200 - $450

When to Call a Professional

Error codes persist after all DIY checks

Water leakage, unusual noises, or burning smells accompany codes

Error codes indicating internal electronics failure (e.g., control board)

Preventive Maintenance

• Clean drain filter regularly: Drainage-related error codes and slow draining
  Frequency: monthly
• Check door seal and latch for debris: Door lock error codes
  Frequency: monthly

Frequently Asked Questions

Why is my Electrolux Washer Dryer showing error codes?

Error codes can occur due to water inlet issues, drainage blockages, or door lock faults.

How do I fix Electrolux Washer Dryer error codes myself?

You can check the drain filter, ensure the door is closed, and inspect water supply hoses.

How much does it cost to fix error codes?

Professional repairs range from $50 for door locks to $450 for control board services.

When should I call a technician for error codes?

If DIY solutions fail or if the issue involves complex components, consider calling a technician.

References & Sources

• Washing Machine common error codes & fixes Official
• How to fix Error Code Issues of Electrolux Washer Dryers Official

User Suggested Solutions