Electrolux Dryer: vibrating noise

Professional Repair Guide

What is this symptom?

Is your Electrolux dryer making a vibrating noise? This noticeable vibration can cause shaking or movement during operation, often accompanied by thumping or rattling sounds. Common causes include an unleveled dryer, unbalanced drum load, or worn drum support rollers. Addressing these issues early can prevent further damage and ensure your dryer operates smoothly.

Urgency: Medium

Important Tips for Electrolux Models

  • Electrolux official troubleshooting specifically notes that newly installed units may vibrate if shipping bolts are not removed and emphasizes leveling of the unit.

Possible Causes

Unleveled Dryer

How to Identify: Dryer rocks or shifts on the floor, vibration reduces when feet are adjusted; uneven surface noted.

Part: Leveling legs / floor contact

Unbalanced or Overloaded Drum Load

How to Identify: Heavy or uneven items like towels/blankets concentrated on one side; vibration decreases when load is redistributed.

Part: Drum internal load distribution

Worn Drum Support Rollers or Axles

How to Identify: Drum may wobble or vibrate excessively; worn rubber on rollers; noise increases as drum turns.

Part: Drum support rollers/axles

Worn Idler Pulley / Belt Tension Issues

How to Identify: Noise and vibration from belt area, belt slipping or rattling, uneven drum movement.

Part: Idler pulley and drive belt

Worn or Damaged Blower Wheel

How to Identify: Rattling or vibrating from blower area; airflow issues may accompany vibration.

Part: Blower wheel

Worn Drum Bearings / Felt Seals

How to Identify: Grinding noises, drum does not spin smoothly by hand; vibration that increases over cycles.

Part: Drum bearings and felt seals

DIY Solutions

Level the Dryer

Easy 10-15 minutes
Tools Needed: level tool, wrench for leveling legs
  1. Use a level tool on top of the dryer to check alignment.
  2. Adjust the leveling legs by turning them so all feet contact the floor evenly.
  3. Recheck with the level and run a short cycle to see if vibration is reduced.
⚠️ Safety First: Ensure the dryer is disconnected from power before moving it.

Redistribute Dryer Load

Easy 5 minutes
  1. Stop the dryer and open the door.
  2. Evenly distribute items inside the drum, ensuring heavy items are balanced.
  3. Avoid overloading the dryer and run a cycle again.

Inspect and Replace Drum Support Rollers

Moderate 60-90 minutes
Tools Needed: screwdriver set, nut driver, replacement roller kit
  1. Disconnect power to the dryer.
  2. Remove access panels to expose the drum and support rollers.
  3. Inspect rollers for wear or flat spots and replace with new ones.
  4. Reassemble panels and test dryer operation.
⚠️ Safety First: Ensure power is disconnected before internal access.

Professional Repairs

Replace Idler Pulley and Drive Belt

Estimated Cost: $80 - $150

Replace Blower Wheel

Estimated Cost: $70 - $130

Replace Drum Bearings / Motor Service

Estimated Cost: $150 - $350

When to Call a Professional

Vibration persists after leveling and load adjustments
Unusual grinding or grinding metal-on-metal noises
Visible damage to internal components like rollers or blower wheel

Preventive Maintenance

  • Level dryer periodically: Vibration due to uneven floor contact
    Frequency: as needed or during installation
  • Clean lint and check for foreign objects: Noise and imbalance from trapped items
    Frequency: after every few cycles

Frequently Asked Questions

Why is my Electrolux Dryer vibrating noise?
Common causes include an unleveled dryer, unbalanced load, or worn drum support rollers.
How do I fix Electrolux Dryer vibrating noise myself?
You can level the dryer, redistribute the load, or inspect drum support rollers for wear.
How much does it cost to fix vibrating noise?
Professional repairs range from $70 to $350 depending on the issue.
When should I call a technician for vibrating noise?
Call a technician if DIY solutions do not resolve the issue or if you suspect major component failures.

References & Sources

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

70%
DIY Success Rate Difficulty: Either

Common Issues Reported by Users

  • Unbalanced load or overloaded drum
  • Worn or damaged drum rollers or bearings
  • Loose or damaged dryer belt
  • Clogged blower fan or dryer vent

User Suggested Solutions

  1. Redistribute the load in the dryer to ensure it is balanced. Avoid overloading the drum.

  2. Inspect and replace worn or damaged drum rollers or bearings. Remove the dryer drum to access these parts.

  3. Check the dryer belt for any signs of wear or damage. Replace if necessary by removing the front panel.

  4. Clean the blower fan and dryer vent to ensure proper airflow and reduce noise.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. New Dryer Noise

Community Discussions

vibrating noise

Check for lint clog in the blower fan and clean the dryer vent.

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!