Beko Washer Dryer: grinding noise before drum spins

Professional Repair Guide

What is this symptom?

Experiencing a grinding noise from your Beko washer dryer just before the drum spins? This unusual sound suggests potential issues such as worn drum bearings or foreign objects caught in the machine. It's essential to identify the source of the noise, as it may indicate friction or wear in mechanical components that could lead to further damage if not addressed promptly.

Urgency: Medium

Important Tips for Beko Models

Beko support acknowledges that highâ€‘pitch or grinding noise is not normal and recommends professional inspection if basic checks do not resolve it

Possible Causes

Worn drum bearings causing friction and grinding noise

How to Identify: Grinding or rumbling noise that intensifies with spin speed and often rough drum feel when manually rotated

Part: Drum bearings

Foreign objects (coins, buttons) trapped between drum and tub or in pump

How to Identify: Noise often accompanied by rattling; small items found in drum holes or pump filter after inspection

Part: Drum interior / pump area

Worn motor coupling or transmission components

How to Identify: Grinding noise with hard starts or inconsistencies in drum spin; diagnosed after other common causes ruled out

Part: Motor coupling / transmission

DIY Solutions

Check for foreign objects in drum and pump filter

Easy 15â€“30 minutes

Tools Needed: flashlight, screwdriver (if needed for pump filter)

Unplug the machine and open the door
Inspect the drum and drum holes for small items
Locate and remove the pump filter (per user manual), clear any debris or objects
Manually spin the drum to check if noise persists

⚠️ Safety First: Always disconnect power before accessing internal parts

Inspect and adjust/replace drive belt

Moderate 30â€“60 minutes

Tools Needed: screwdriver set, socket set

Disconnect power and move machine to access rear panel
Remove rear panel to expose drive belt
Inspect belt for wear, cracks or slack
If worn, install correct replacement belt ensuring proper alignment and tension
Reassemble panels and test machine

⚠️ Safety First: Ensure machine is unplugged and properly supported

Professional Repairs

Drum bearing replacement

Estimated Cost: $150 - $400

Motor coupling or transmission repair/replacement

Estimated Cost: $120 - $350

When to Call a Professional

If grinding noise continues after removing foreign objects and inspecting belt

If bearings are suspected (intense grinding at higher speeds)

If machine fails to spin or shows other mechanical performance issues

Preventive Maintenance

Check pockets before every load: Objects entering drum or pump causing noise
Frequency: Every use
Ensure load is balanced and within capacity: Stress on bearings and drive components
Frequency: Every use

Frequently Asked Questions

Why is my Beko Washer Dryer grinding noise before drum spins?

The grinding noise may be caused by worn drum bearings, foreign objects trapped in the drum, or issues with motor coupling.

How do I fix Beko Washer Dryer grinding noise before drum spins myself?

You can check for foreign objects in the drum and inspect the pump filter. Additionally, inspect the drive belt for wear.

How much does it cost to fix grinding noise before drum spins?

Professional repairs for this issue can range from $150 to $400 for drum bearing replacement or $120 to $350 for motor coupling repairs.

When should I call a technician for grinding noise before drum spins?

If DIY checks do not resolve the issue, or if the noise persists, it's best to consult a technician to prevent further damage.

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

65%

DIY Success Rate Difficulty: Either

Common Issues Reported by Users

Worn or damaged drum bearings
Foreign object trapped in the drum or pump
Faulty motor coupling or drive belt

User Suggested Solutions

Inspect and replace drum bearings. Disconnect the power, remove the back panel, and check the bearings for wear. If damaged, replace them with new ones.
Check for foreign objects. Open the door and inspect the drum and pump filter for any items that may be causing the noise. Remove any found objects.
Examine and replace the motor coupling or drive belt. Disconnect power, remove the front panel, and inspect the components. Replace if worn or broken.