Beko Dryer: fan failure

Professional Repair Guide

What is this symptom?

Experiencing fan failure in your Beko dryer? This issue leads to poor airflow, ineffective drying, and clothes remaining damp. Error codes like E13 may appear, indicating airflow faults. It's essential to diagnose and address the problem to restore your dryer's performance.

Urgency: Medium

Important Tips for Beko Models

Some Beko washerâ€‘dryer combos may report an E13 error code for dryer fan/airflow faults indicating failed fan motor, obstructed fan wheel, blocked air ducts or wiring issues

Possible Causes

Blocked air path (lint/duct obstruction)

How to Identify: Reduced airflow at exhaust vent; clothes not drying fully despite heating; lint visible in filter and ducts

Part: Lint filter / vent ducts

Failed blower/fan motor

How to Identify: No airflow even after clearing vents; fan doesnâ€™t spin when inspecting interior; unusual noises (grinding/humming from motor area

Part: Dryer fan motor / blower assembly

Obstructed or jammed fan wheel/blower wheel

How to Identify: Fan blade wonâ€™t spin freely by hand; debris (lint/clothes threads caught in blades

Part: Fan wheel / blower wheel

Wiring fault to fan motor

How to Identify: Intermittent operation or no fan activity with no other visible faults; diagnostic error codes relating to airflow/fan

Part: Wiring harness / connectors to fan motor

DIY Solutions

Clean lint filter and exhaust vent

Easy 15-30 minutes

Tools Needed: vacuum with crevice tool, vent brush

Unplug dryer.
Remove and clean internal lint filter of all lint.
Detach exhaust vent hose and inspect for lint buildup.
Use vent brush/vacuum to clear lint/debris from ducts and vents.
Reassemble and test dryer airflow.

⚠️ Safety First: Ensure dryer is unplugged before accessing internal vents.

Inspect and clear fan blades

Moderate 30-60 minutes

Tools Needed: screwdriver set, flashlight, gloves

Unplug dryer and access rear or internal panel following manual guidance.
Locate the blower/fan assembly inside dryer.
Check fan blades for lint, debris, or trapped items.
Remove obstruction manually and ensure fan spins freely by hand.
Reassemble panels and restore power to test.

⚠️ Safety First: Disconnect power before accessing internal parts.

Professional Repairs

Replace fan motor or blower assembly

Estimated Cost: $100 - $300

Repair/replace wiring harness to fan

Estimated Cost: $80 - $180

When to Call a Professional

Fan motor does not run after cleaning vents and clearing obstructions

Unusual noises from inside fan assembly indicating mechanical failure

Electrical issues suspected (burn marks, wiring damage)

Preventive Maintenance

Clean lint filter: Lint buildup causing restricted airflow and fan strain
Frequency: After every load
Inspect and clean exhaust duct annually: Vent obstruction and excessive strain on fan and motor
Frequency: Annually

Frequently Asked Questions

Why is my Beko Dryer fan failing?

Common causes include blocked air paths, a failed blower motor, or obstructions in the fan.

How do I fix Beko Dryer fan failure myself?

Start by cleaning the lint filter and exhaust vent, then inspect and clear the fan blades.

How much does it cost to fix fan failure?

Professional repairs range from $100 to $300 for fan motor replacement or $80 to $180 for wiring repairs.

When should I call a technician for fan failure?

If DIY solutions don't resolve the issue or if you suspect complex electrical faults, contact a technician.

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

75%

DIY Success Rate Difficulty: Either

Common Issues Reported by Users

Burnt or broken heater fan motor
Blocked or clogged air vents
Faulty thermal fuse or thermostat

User Suggested Solutions

Inspect and replace the heater fan motor. Disconnect the dryer from power, remove the back panel, and locate the fan motor. Check for visible damage or burnt wires. If damaged, replace with a new motor following the manufacturer's instructions.
Clean the air vents and ducts. Disconnect the dryer from power, and use a vacuum to remove lint and debris from the vents. Ensure that the airflow is unobstructed to prevent overheating.
Test and replace the thermal fuse or thermostat. After disconnecting power, locate the thermal fuse or thermostat within the dryer. Use a multimeter to test for continuity. Replace if faulty.