Fisher & Paykel Dishwasher Error F2
⚡ Quick Answer: The Fisher & Paykel dishwasher error F2 signifies a problem with the drain pump, often resulting in the appliance stopping mid-cycle, unusual noises, ... ✅ DIY Fixable
What Does Error F2 Mean?
The Fisher & Paykel dishwasher error F2 signifies a problem with the drain pump, often resulting in the appliance stopping mid-cycle, unusual noises, and failure to drain water. This issue may stem from a motor or motor rotor fault, or a drainage and water level problem, requiring thorough inspection for resolution.
Common Symptoms:
- Dishwasher stops mid-cycle with F2 displayed
- Beeping and failure to start or complete wash cycle
- Display of F2 in LED or fault indicator
Possible Causes
- Motor or motor rotor fault (medium)
- Drainage or water level issue (medium)
How to Fix Error F2
DIY Fix Basic checks and reset
- Turn off power to the dishwasher (unplug or switch off breaker).
- Wait a few minutes to allow control board to reset.
- Ensure the dishwasher drain filter and sump are clear of debris.
- Restart the dishwasher and observe if F2 returns.
Technician Only Inspect motor/motor rotor and drainage system
- Verify error code with diagnostic mode if available on model.
- Check motor and rotor assembly for continuity and physical damage.
- Inspect and clear any drain hose kinks or blockages.
- Test water level sensors and related wiring.
- Replace faulty motor/rotor or sensor components as needed.
Parts needed: motor/rotor assembly, drain hose, water level sensor
- If F2 reappears after basic reset and filter/drain checks
- If unusual noises occur during operation
- If you are not comfortable performing mechanical checks
Next step
Choose the next step for F2
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
- Typical part-only price
- $15 - $30
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Pressure Switch
Detects the water level inside the tub and signals when to start or stop filling.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 50W |
|---|---|
| component | Drain Pump |
| resistance | 10-20 ohms |
| part_number | FP-DW-DRP-01 |
| voltage_rating | 240V AC |
Common Questions
What does F2 error mean on Fisher & Paykel dishwasher?
F2 indicates a drain pump failure, causing the dishwasher to stop mid-cycle and fail to drain.
Can I fix Fisher & Paykel dishwasher F2 error myself?
Yes, you can perform basic checks like resetting the power and cleaning the drain filter.
How much does it cost to fix F2 error?
The estimated repair cost ranges from $100 to $400, depending on parts and labor.
When should I call a technician for F2?
Call a technician if F2 reappears after a reset or if you're uncomfortable with mechanical checks.
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!