Electrolux Oven Error F31
⚡ Quick Answer: The Electrolux oven error F31 indicates a fault with the temperature sensor circuit, often caused by a shorted temperature probe or issues with the wi... ⚠️ Difficulty Varies
What Does Error F31 Mean?
The Electrolux oven error F31 indicates a fault with the temperature sensor circuit, often caused by a shorted temperature probe or issues with the wiring. This error typically results in erratic temperature readings, failure to heat properly, or the oven shutting down unexpectedly. Addressing this issue involves inspecting the temperature sensor and its wiring for faults.
Common Symptoms:
- Error code F31 displayed on oven control panel
- Oven fails to heat or regulate temperature correctly
- Oven may shut down or refuse to start heating cycles
Possible Causes
- Oven temperature sensor (RTD) short circuit or failure (high)
- Wiring harness short between sensor and control board (medium)
How to Fix Error F31
DIY Fix Basic reset attempt
- Turn off oven power at breaker or unplug for at least 30 seconds
- Restore power and attempt a fresh start
Technician Only Inspect / test temperature sensor (RTD) and wiring
- Disconnect oven from power
- Access oven interior and locate the temperature sensor (usually a probe at back wall)
- Disconnect sensor and measure resistance with multimeter at room temperature
- Replace sensor if resistance is very low (short) or infinite (open)
- Inspect wiring harness and connectors for signs of shorts or insulation damage and repair/replace as needed
Parts needed: Oven temperature sensor (RTD), Wiring harness / connectors
- If error reappears after sensor and wiring checks/replacements
- If control board shows other signs of failure or damage
Next step
Choose the next step for F31
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Oven parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Non-Scratch Cooktop Cleaner
A routine surface-care product. Confirm that it is approved for the specific glass, ceramic, enamel, or stainless finish.
Oven Thermometer
A diagnostic aid for comparing cavity temperature during a controlled check. It does not prove which internal component has failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | N/A |
|---|---|
| component | Temperature Sensor |
| resistance | 10,000 ohms at 25°C |
| part_number | 318255100 |
| voltage_rating | 120V AC |
Common Questions
What does F31 error mean on electrolux oven?
F31 indicates a malfunction in the temperature sensor circuit, leading to heating issues.
Can I fix electrolux oven F31 error myself?
You can try a basic reset by turning off the power for 30 seconds, but further inspection may be needed.
How much does it cost to fix F31 error?
Repair costs range from $30 to $150 for parts, with additional technician labor costs.
When should I call a technician for F31?
Call a technician if the error persists after checking or replacing the sensor and wiring.
Sources & References
- Electrolux Range Error Code F31 - Shorted Probe (official)
- Electrolux Oven Error Codes Guide (F30/F31) (community)
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!