Asko Dishwasher Error F8
⚡ Quick Answer: The F8 error on your Asko dishwasher indicates a potential issue with the drain pump, often caused by a clogged or dirty filter. This error usually ap... ✅ DIY Fixable
What Does Error F8 Mean?
The F8 error on your Asko dishwasher indicates a potential issue with the drain pump, often caused by a clogged or dirty filter. This error usually appears towards the end of a cycle and may be accompanied by low water flow or circulation issues. In some models, you might also see a 'clean filter' alert. To resolve this, inspect and clean the filters and sump area to ensure proper drainage.
Common Symptoms:
- Dishwasher displays F8 typically after or near end of cycle
- Low water flow or circulation detected corresponding with pressure readings
- Possible alert to ‘clean filter’ message in display on some models
Possible Causes
- Clogged or dirty filter restricting water flow (medium)
- Debris or obstruction in sump/pressure chamber below filter (medium)
- Faulty pressure sensor incorrectly signaling low pressure (low)
How to Fix Error F8
DIY Fix Clean Filter and Remove Obstructions
- Open dishwasher and locate coarse and fine filters at bottom of tub.
- Remove filters and rinse under running water to clear food debris.
- Check and clear any visible debris in sump area under filters.
- Reinstall filters securely and restart dishwasher.
Technician Only Inspect and Test Pressure Sensor and Internal Components
- Disconnect power and access dishwasher base or front panel.
- Inspect pressure sensor tubing and sensor for blockages or damage.
- Test pressure sensor electrical function with multimeter and replace if defective.
- Verify sump area and circulation components are clean and unobstructed.
Parts needed: pressure sensor, filters, possibly sump components
- If cleaning filters and sump does not clear error
- If electrical testing identifies a defective pressure sensor
- If error recurs repeatedly indicating internal fault
Next step
Choose the next step for F8
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
- Typical part-only price
- $35 - $80
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 50W |
|---|---|
| component | Drain Pump |
| resistance | 10-30 ohms |
| part_number | ASKO 8051375 |
| voltage_rating | 120V AC |
Common Questions
What does F8 error mean on asko dishwasher?
F8 indicates a malfunction in the drain pump, often due to a clogged filter.
Can I fix asko dishwasher F8 error myself?
Yes, you can clean the filters and remove obstructions from the sump.
How much does it cost to fix F8 error?
Estimated repair costs range from $50 to $250, depending on the necessary parts or labor.
When should I call a technician for F8?
Call a technician if cleaning does not resolve the error or if it recurs frequently.
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!