AEG Dryer Error C8
⚡ Quick Answer: The AEG Dryer error code C8 indicates a malfunction in the temperature sensor, which can prevent the dryer from producing heat or completing its cycle... ⚠️ Difficulty Varies
What Does Error C8 Mean?
The AEG Dryer error code C8 indicates a malfunction in the temperature sensor, which can prevent the dryer from producing heat or completing its cycle. This issue often arises from a defective temperature sensor that requires attention to restore proper functionality.
Common Symptoms:
- Dryer stops with code C8 displayed
- Dryer may not heat properly or complete cycle
Possible Causes
- Defective or faulty temperature sensor (high)
How to Fix Error C8
DIY Fix Basic checks before technician visit
- Turn off the dryer and unplug it from the mains.
- Wait a few minutes and plug it back in to see if the error clears (simple reset).
- Ensure lint filters and air pathways are clean to prevent secondary errors.
Technician Only Diagnose and replace temperature sensor
- Use diagnostic mode if available to confirm sensor fault.
- Inspect temperature sensor wiring and connector for damage or corrosion.
- Test the temperature sensor resistance/response with a multimeter to confirm failure.
- Replace defective temperature sensor with OEM part.
- Verify operation and clear error codes after repair.
Parts needed: Temperature sensor (NTC thermistor), Sensor wiring harness
- If the error persists after reset and basic checks, do not attempt further DIY fixes.
- If dryer continues to refuse to heat or complete cycles and C8 remains displayed.
Next step
Choose the next step for C8
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Dryer parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dryer Vent Cleaning Kit
Helps remove routine lint buildup from an accessible dryer vent path. It does not diagnose or repair an E-code or failed component.
Lint Trap Cleaning Brush
A narrow brush for routine cleaning around an accessible lint screen and housing.
Dryer Vent Hose Kit
A replacement exhaust duct option for visibly crushed or damaged external venting. Check diameter, length, local code, and installation clearance.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does C8 error mean on AEG Dryer?
C8 error indicates a malfunction in the temperature sensor, preventing proper heating.
Can I fix AEG Dryer C8 error myself?
You can try resetting the dryer and checking lint filters, but further issues require a technician.
How much does it cost to fix C8 error?
Repair costs range from $80 to $200, depending on parts and labor in your region.
When should I call a technician for C8?
Call a technician if the error persists after a reset or if the dryer won't heat or complete cycles.
Sources & References
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!