Miele Dishwasher Error F51
⚡ Quick Answer: The Miele Dishwasher F51 error code indicates a malfunction with the pump pressure level switch, which may prevent proper drainage and cause the dishw... ✅ DIY Fixable
What Does Error F51 Mean?
The Miele Dishwasher F51 error code indicates a malfunction with the pump pressure level switch, which may prevent proper drainage and cause the dishwasher to stop mid-cycle. This issue can be triggered by a blockage in the pressure sensing hose or a faulty pressure sensor, leading to unusual noises and failure to fill or drain correctly.
Common Symptoms:
- Dishwasher stops mid‑cycle when F51 appears
- Display shows fault F51
- Possible failure to fill or drain correctly depending on model
Possible Causes
- Pump pressure level switch fault (high)
- Pressure/level sensor or hose blockage or fault (medium)
How to Fix Error F51
DIY Fix Basic checks before calling technician
- Turn off and disconnect dishwasher from power.
- Visually inspect for obvious blockages near the base and filters and clean them.
- Check pressure hose under the base for kinks or disconnections if easily accessible.
Technician Only Diagnose and replace faulty pressure switch or related component
- Access dishwasher’s internal base panel and locate the pressure level switch and associated hoses.
- Check continuity and operation of the pressure switch and inspect pressure hose for blockages or damage.
- Replace defective pressure switch, sensor, or hose as needed.
- Run diagnostic cycle to confirm resolution.
Parts needed: Pressure level switch, Pressure sensing hose, Possible pressure sensor
- If error persists after basic checks
- If internal components are inaccessible or diagnosis uncertain
Next step
Choose the next step for F51
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
- Typical part-only price
- $35 - $80
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does F51 error mean on Miele Dishwasher?
F51 indicates a malfunction in the pump pressure level switch, causing the dishwasher to stop mid-cycle.
Can I fix Miele Dishwasher F51 error myself?
Yes, you can perform basic checks like inspecting for blockages and checking the pressure hose before calling a technician.
How much does it cost to fix F51 error?
Estimated repair costs for the F51 error range from $150 to $400, depending on parts and labor.
When should I call a technician for F51?
Call a technician if the error persists after basic checks or if internal components are inaccessible.
Sources & References
- Miele Dishwasher Fault F51 Support Page (official)
- Miele UK Support - Fault F51 (official)
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!