Kenmore Dryer Error F01
⚡ Quick Answer: The Kenmore Dryer F01 error indicates a malfunction in the main electronic control board, which manages the dryer's functions. This error often preven... ✅ DIY Fixable
What Does Error F01 Mean?
The Kenmore Dryer F01 error indicates a malfunction in the main electronic control board, which manages the dryer's functions. This error often prevents the dryer from starting or causes erratic behavior. If the F01 code appears and persists after a power reset, it typically signifies that the control board is failing and may require replacement.
Common Symptoms:
- Dryer will not start or stops immediately when the error is displayed.
- Display shows F01 and may beep once then shut off.
- Error persists after power reset.
Possible Causes
- Main electronic control board failure (high)
How to Fix Error F01
DIY Fix Power reset of dryer
- Unplug the dryer or disconnect its power supply.
- Wait approximately 10 minutes to allow electronics to fully reset.
- Reconnect power and attempt to start the dryer.
Technician Only Inspect and replace main control board
- Disconnect power to the dryer.
- Remove dryer access panels to reach the main control board.
- Inspect wiring harness connections for looseness or burn damage.
- Test or visually inspect the control board for damage.
- Replace the control board with an OEM or equivalent part if found defective.
Parts needed: Main electronic control board (central control unit), Replacement wiring harness or connectors if damaged
- If diagnostic steps do not clear the error and you are not experienced with appliance electronics.
- If there are signs of electrical damage or burnt components on internal boards.
Next step
Choose the next step for F01
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
- Typical part-only price
- $120 - $280
- DIY difficulty
- Medium
- Estimated time
- 20-40 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Dryer parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dryer Vent Cleaning Kit
Helps remove routine lint buildup from an accessible dryer vent path. It does not diagnose or repair an E-code or failed component.
Lint Trap Cleaning Brush
A narrow brush for routine cleaning around an accessible lint screen and housing.
Dryer Vent Hose Kit
A replacement exhaust duct option for visibly crushed or damaged external venting. Check diameter, length, local code, and installation clearance.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does F01 error mean on Kenmore Dryer?
The F01 error indicates a failure in the main electronic control board, preventing the dryer from starting or causing erratic behavior.
Can I fix Kenmore Dryer F01 error myself?
Yes, you can attempt a power reset by unplugging the dryer for about 10 minutes. If the error persists, further diagnosis may be needed.
How much does it cost to fix F01 error?
The estimated repair cost for the F01 error ranges from $150 to $400, depending on parts and labor.
When should I call a technician for F01?
Call a technician if the error does not clear after a reset or if you notice signs of electrical damage on internal components.
Sources & References
- Kenmore Dryer Code F01 (Beginners Guide) (community)
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!