Hotpoint Dishwasher Error F08
⚡ Quick Answer: The Hotpoint dishwasher F08 error indicates a temperature timeout fault, meaning the water did not reach the expected temperature in the allowed time.... ✅ DIY Fixable
What Does Error F08 Mean?
The Hotpoint dishwasher F08 error indicates a temperature timeout fault, meaning the water did not reach the expected temperature in the allowed time. This malfunction often causes the dishwasher to stop mid-cycle, fail to heat water during washing, and cancel or fail when reaching the heating phase. Common causes include a faulty heating element or issues with the temperature sensor or associated wiring.
Common Symptoms:
- Dishwasher stops mid‑cycle with F08 displayed
- Water does not appear to heat during wash
- Cycle cancels or fails when reaching heating phase
Possible Causes
- Heating element not raising water temperature in expected time (medium)
How to Fix Error F08
DIY Fix Basic restart and observation
- Turn off and disconnect the dishwasher from power (unplug or switch off at breaker).
- Wait a few minutes to allow control electronics to reset.
- Reconnect power and run a short rinse cycle to observe if the code returns.
Technician Only Inspect and service heating circuit
- Verify heating element continuity and function using a multimeter.
- Check temperature sensor/thermostat operation and correct mounting.
- Inspect wiring and connectors around heating element and control board.
- Replace faulty heating element or sensor as required.
Parts needed: Dishwasher heating element, Temperature sensor/thermostat, Associated wiring/connectors
- Error reoccurs after power cycle
- Dishwasher shows signs of electrical fault (burn smell, sparks)
- Water remains cold and cycle consistently fails at heating phase
Next step
Choose the next step for F08
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Heating Element
Heats the water or air inside the appliance to the required temperature.
- Typical part-only price
- $40 - $95
- DIY difficulty
- Medium
- Estimated time
- 30-45 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
Thermostat
Regulates temperature by turning the heating or cooling system on or off.
Wiring Harness
Connects controls, sensors, motors, and other electrical components inside the appliance.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 50W |
|---|---|
| component | Drain Pump |
| resistance | 10-30 ohms |
| part_number | WD19X10015 |
| voltage_rating | 120V AC |
Common Questions
What does F08 error mean on Hotpoint dishwasher?
F08 indicates a temperature timeout fault, where water fails to heat during the wash cycle.
Can I fix Hotpoint dishwasher F08 error myself?
Yes, try restarting the dishwasher by disconnecting power and running a rinse cycle.
How much does it cost to fix F08 error?
Repair costs range from $80 to $250, depending on parts and labor.
When should I call a technician for F08?
Call a technician if the error reoccurs, or if there are signs of electrical faults like burnt smells.
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!