Hoover Dishwasher Error E10
⚡ Quick Answer: The Hoover dishwasher E10 error indicates a drying system fault, typically caused by a malfunctioning drying fan. This error results in poor drying pe... ✅ DIY Fixable
What Does Error E10 Mean?
The Hoover dishwasher E10 error indicates a drying system fault, typically caused by a malfunctioning drying fan. This error results in poor drying performance and may be accompanied by wet dishes at the end of the cycle. Possible causes include a failed drying fan motor, blocked air ducts, or faulty humidity sensors. To resolve this, check for airflow blockages and reset the machine. If the issue persists, professional repair may be necessary.
Common Symptoms:
- Dishes remain very wet at the end of the cycle
- Poor or no drying performance
- Drying fan does not run during drying phase
- Error displayed at end of cycle
Possible Causes
- Failed drying fan motor (medium)
- Blocked air duct / ventilation obstruction (medium)
- Faulty humidity/temperature sensor affecting drying detection (medium)
- Wiring fault between control board and drying components (medium)
How to Fix Error E10
DIY Fix Check for obvious airflow blockages and reset
- Turn off and unplug the dishwasher.
- Open the dishwasher and inspect the venting/air duct areas for plastic packaging, labels, insulation or other obstructions.
- Remove any visible blockages.
- Plug the dishwasher back in and run a short cycle to see if the error clears.
Technician Only Test and replace drying fan assembly
- Disconnect power and remove the relevant access panels to reach the drying fan assembly.
- Visually inspect the fan for obstruction, damage or seized bearings.
- Use a multimeter to test the fan motor continuity; replace the assembly if the motor is open circuit or otherwise faulty.
- Inspect wiring harness and connectors for damage; repair any faults.
- Reassemble and test running a full cycle to confirm resolution.
Parts needed: drying fan motor / fan assembly, air duct parts if blocked/damaged, connector/wiring as needed
- If the error persists after clearing blockages and resetting.
- If you are not comfortable accessing internal dishwasher components.
- If wiring or electronic control faults are suspected.
Next step
Choose the next step for E10
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
- Typical part-only price
- $15 - $35
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| note | The previous model-independent part specification was removed. Verify the full model number and diagnosis in the manufacturer's official parts catalog before ordering. |
|---|---|
| part_number | None |
Common Questions
What does E10 error mean on Hoover dishwasher?
E10 error indicates a drying system fault, often resulting in wet dishes due to a malfunctioning drying fan.
Can I fix Hoover dishwasher E10 error myself?
Yes, you can check for airflow blockages and reset the dishwasher as initial troubleshooting steps.
How much does it cost to fix E10 error?
The estimated cost to repair the E10 error ranges from ¥8,000 to ¥25,000, depending on parts and region.
When should I call a technician for E10?
Call a technician if the error persists after clearing blockages or if you're uncomfortable accessing internal components.
Data last verified: 2026-07-31
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!