None Washing Machine: making noise
What is this symptom?
Is your washing machine making loud, unusual noises during operation? This can include banging, grinding, or excessive vibrations, especially during the spinning and draining cycles. The noise may vary depending on the load size or distribution, indicating potential issues that need addressing.
Possible Causes
Unbalanced load or uneven laundry distribution
How to Identify: Noise occurs during spin/agitation; loud banging/thumping and excessive vibration; often improves after redistributing clothes evenly. Overstuffed or very light loads cause imbalance.
Part: Drum / Load distribution
Loose items inside drum (coins, small hardware)
How to Identify: Sharp clanking sounds, especially at drum periphery; found when inspecting drum after stopping cycle.
Part: Drum interior
Worn drum bearings or spider assembly
How to Identify: Deep rumbling or grinding noise that gets louder with spin speed; persists despite balanced load.
Part: Bearings / Spider arm
Faulty or worn out pump
How to Identify: Whining or grinding noise during drain cycles; possible water not draining properly.
Part: Drain pump
DIY Solutions
Redistribute laundry for balanced load
- Pause the washer mid-cycle via control panel.
- Open door and evenly redistribute clothes around the drum.
- Remove excess items to meet recommended load capacity.
- Restart cycle and listen for reduced noise.
Level the washing machine
- Place level on top of machine to check horizontal alignment.
- Adjust adjustable feet by turning to raise/lower corners.
- Re‑check level and tighten lock nuts on feet.
- Run an empty spin cycle to confirm noise reduction.
Remove foreign objects from drum
- Stop cycle and open drum door.
- Visually inspect drum and rubber gasket for small items.
- Remove any debris or objects found.
- Run a rinse/spin to see if noise improves.
Next step
Choose the next step for making noise
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drum Bearing Kit
Supports the spinning drum and ensures smooth, quiet rotation during cycles.
- Typical part-only price
- $40 - $95
- DIY difficulty
- Hard
- Estimated time
- 120-180 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace drum bearings / spider assembly
Drain pump cleaning or replacement
When to Call a Professional
Preventive Maintenance
-
Check and clean drum and gasket for debris: Noise from foreign objects and improves balance
Frequency: monthly -
Level machine and check feet: Vibration and noise from uneven placement
Frequency: every 6 months -
Avoid overloading and uneven loads: Imbalance and excess stress on components
Frequency: each wash
Frequently Asked Questions
Why is my Any Washing Machine making noise?
How do I fix Any Washing Machine making noise myself?
How much does it cost to fix making noise?
When should I call a technician for making noise?
References & Sources
- 5 Reasons Your Washer is Making Loud Noise Repair-Blog
- Washing machine noise and countermeasures Community
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Faulty spider arm support bracket or spider assembly (1 mentions)
- Improperly secured heating element (1 mentions)
User Suggested Solutions
-
Check if the heating element is properly secured in its bracket
-
Inspect and potentially replace the spider arm support bracket or spider assembly
-
Consider replacing the washing machine if recommended by a repair professional
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
making noise after replacing the heating element
Check if the heating element is properly secured in its bracket to prevent contact with the drum.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!