None Washing Machine: excessive shaking and noise
What is this symptom?
Is your washing machine shaking excessively and making loud noises during the spin cycle? This common issue can stem from unbalanced loads, improper leveling, or worn components. Identifying the cause will help restore your machine's performance and prevent further damage.
Possible Causes
Unbalanced or uneven laundry load
How to Identify: Shaking starts during spin; loud banging; heavy or bulky items (towels/blankets are unevenly placed in drum.
Part: Drum/Load distribution
Machine not level or feet improperly adjusted
How to Identify: Washing machine rocks if pushed, water level in built‑in level indicator isn’t centered, noises vary with floor surface.
Part: Leveling feet/Base
Worn or failed shock absorbers/dampers
How to Identify: Persistent vibration even with balanced loads and level floor, knocking noises, older machines.
Part: Shock absorbers/Suspension dampers
Loose or worn suspension springs
How to Identify: Internal banging or thumping, vibration remains after load and level checks.
Part: Suspension springs
Hard floor amplifying vibration
How to Identify: Vibration transmits strongly into surrounding cabinetry or floorboards.
Part: Installation surface
Internal component wear (bearings, motor mount)
How to Identify: Grinding or rumbling noises, vibration persists regardless of load or leveling.
Part: Bearings/motor mount
DIY Solutions
Redistribute laundry evenly
- Stop the washer mid‑cycle.
- Rearrange laundry so heavy items are spread evenly around the drum.
- Restart the cycle.
Level the washing machine
- Turn off and unplug the washer.
- Use a spirit level on top of the machine.
- Adjust each leveling foot until the machine is level.
- Retighten lock nuts on feet and test with a small load.
Use anti‑vibration pads or mat
- Purchase anti‑vibration pads or a dedicated washer mat.
- Place pads under each foot or lay mat under the washer.
- Test run to assess vibration reduction.
Next step
Choose the next step for excessive shaking and noise
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Washer Shock Absorber
Dampens tub movement and vibration during high-speed spin cycles.
- Typical part-only price
- $25 - $100
- DIY difficulty
- Medium
- Estimated time
- 45-90 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace shock absorbers/dampers
Replace suspension springs
Replace drum bearings or motor mounts
When to Call a Professional
Preventive Maintenance
-
Check and adjust leveling feet periodically: Excessive vibration
Frequency: quarterly -
Clean and balance loads correctly each wash: Imbalance‑induced vibration
Frequency: each use -
Inspect shock absorbers/springs after ~5 years: Component wear effects
Frequency: annually
Frequently Asked Questions
Why is my Any Washing Machine excessive shaking and noise?
How do I fix Any Washing Machine excessive shaking and noise myself?
How much does it cost to fix excessive shaking and noise?
When should I call a technician for excessive shaking and noise?
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Unbalanced load or improper loading of the washing machine
- Worn or damaged suspension rods or shock absorbers
- Improper leveling of the washing machine
- Faulty or insufficient damper grease
- Worn out or broken springs
User Suggested Solutions
-
Check and redistribute the load inside the washing machine. Ensure that heavy items are balanced with lighter ones. If necessary, remove some items and run a smaller load.
-
Inspect the suspension rods and shock absorbers for wear or damage. Replace any faulty parts as needed. This may require removing the outer casing of the machine.
-
Level the washing machine by adjusting the feet. Use a level tool to check alignment and make adjustments until the machine is even.
-
Apply or replace damper grease on the suspension system to ensure proper operation. Consult the user manual for specific instructions on accessing the suspension.
-
Inspect and replace any worn or broken springs in the washing machine. This may involve disassembling parts of the machine to access the springs.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
shakes violently and is extremely loud
Insufficient damper grease may be causing the issue; leveling the machine and checking suspension rods are recommended.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!