None Washer Dryer: not draining

Possible Causes

Clogged drain hose

How to Identify: Water stays in drum; inspect hose for kinks, bends, or blockages; reduced or no water flow out of hose.

Part: Drain hose

Clogged drain pump or internal debris

How to Identify: Water not draining even after hose/filter cleaning; unusual noises from pump area; pump may be blocked by small objects.

Part: Drain pump

Faulty drain pump (motor failure)

How to Identify: No sound or weak sound from pump when attempting to drain; electrical test of pump shows no operation.

Part: Drain pump motor

Water level sensor or control board malfunction

How to Identify: No drain action despite clear hoses and filters; error codes persist; diagnostics point to sensor/control errors.

Part: Water level sensor / control board

DIY Solutions

Check and clear drain hose

Moderate 15-30 minutes

Tools Needed: screwdriver, bucket

1. Unplug machine and turn off water
2. Move unit to access back, inspect drain hose for kinks or bends
3. Disconnect hose and flush with water to clear debris
4. Reconnect hose ensuring correct height and no sharp bends

⚠️ Safety First: Ensure power is off before accessing hoses

Clean lint/trap filter

Easy 10-20 minutes

Tools Needed: towel, bucket

1. Locate lint/trap filter access (often bottom front)
2. Place towel/bucket to catch water
3. Unscrew/filter cover and remove accumulated lint and debris
4. Rinse filter and replace securely

⚠️ Safety First: Expect some water to spill when removing filter

Inspect and clean drain pump debris

Advanced 30-60 minutes

Tools Needed: screwdrivers, pliers, bucket

1. Unplug and tip unit carefully to access bottom panel
2. Remove cover to expose drain pump
3. Inspect pump inlet/outlet for debris and remove
4. Reassemble and test draining

⚠️ Safety First: Disconnect power before opening access panels

Next step

Choose the next step for not draining

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Drain Hose

Carries waste water from the drain pump to your home's standpipe or sink drain.

Typical part-only price

$15 - $30

DIY difficulty

Easy

Estimated time

15-30 mins

Optional: enter your model number

Apply

Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Possible related component

Drain Pump

Pumps waste water out of the appliance during the drain cycle.

$35 - $80 · Easy · 15-30 mins

Check fit & price

Possible related component

Pressure Switch

Detects the water level inside the tub and signals when to start or stop filling.

$25 - $65 · Easy · 15-30 mins

Check fit & price

Possible related component

Main Control Board

The central brain of the appliance that controls all components, cycles, and timings.

$120 - $280 · Medium · 20-40 mins

Check fit & price

Model number required

Model-compatible Washer Dryer parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Dryer Vent Cleaning Kit

Helps remove routine lint buildup from an accessible dryer vent path. It does not diagnose or repair an E-code or failed component.

View maintenance supply

Maintenance supply

Lint Trap Cleaning Brush

A narrow brush for routine cleaning around an accessible lint screen and housing.

View maintenance supply

Maintenance supply

Dryer Vent Hose Kit

A replacement exhaust duct option for visibly crushed or damaged external venting. Check diameter, length, local code, and installation clearance.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace drain pump assembly

Estimated Cost: $80 - $200

Control board or water level sensor repair/replacement

Estimated Cost: $150 - $400

When to Call a Professional

Water remains after all basic checks and DIY cleaning attempts

Unusual noises from pump after removing blockages

Error codes indicating internal faults that persist after clearing hoses/filters

Preventive Maintenance

• Clean lint/trap filter: Filter blockages that impede drain flow
  Frequency: weekly to monthly
• Inspect drain hose alignment: Hose kinks or bends that restrict drainage
  Frequency: quarterly

Frequently Asked Questions

Why is my Any Washer Dryer not draining?

The common causes include a clogged drain hose, debris in the pump, or a faulty drain pump.

How do I fix Any Washer Dryer not draining myself?

You can check and clear the drain hose, clean the lint trap, or inspect the drain pump for debris.

How much does it cost to fix not draining?

Professional repairs can range from $80 to $400, depending on whether you need to replace the drain pump or control board.

When should I call a technician for not draining?

If DIY solutions do not resolve the issue or if you encounter complex problems, it's time to call a technician.

References & Sources

• Washer machine not draining - maintenance guide Repair-Blog
• Comprehensive drain troubleshooting Repair-Blog

Common Issues Reported by Users

• Drain pump malfunction (2 mentions)
• Clogged filter (1 mentions)
• Pressure switch failure (1 mentions)

User Suggested Solutions

1. Check and replace the drain pump

2. Clean the filter