Samsung Dryer: not igniting
What is this symptom?
Is your Samsung gas dryer not igniting? If the dryer powers on and tumbles but fails to ignite the burner, several issues could be at play. Common causes include igniter failure, faulty gas valve solenoid coils, or gas supply problems. This guide will help you troubleshoot and resolve the ignition issue effectively.
Important Tips for Samsung Models
- Common ignition/heat issues include igniter and gas valve solenoid failures.
Possible Causes
Igniter failure
How to Identify: Dryer runs but no ignition; igniter does not glow when tested with multimeter or visible test.
Part: Igniter
Gas valve solenoid coils failed
How to Identify: Igniter may glow but gas does not flow or burner does not light; multimeter testing of solenoid coils shows no continuity.
Part: Gas valve solenoid
Flame sensor or flame detection failure
How to Identify: Igniter glows but flame is not detected and dryer shuts off; error codes or diagnostic may indicate flame sense fault.
Part: Flame sensor
Thermal fuse or safety cutoff blown
How to Identify: Dryer runs but heat circuit is interrupted; thermal fuse tests open continuity with multimeter.
Part: Thermal fuse
Gas supply issue (valve off or gas line problem)
How to Identify: No gas flow indicated by smell or gas pressure test; ensure gas valve open at house supply.
Part: Gas supply
DIY Solutions
Test and replace igniter
- Disconnect power and gas supply.
- Access igniter assembly near burner box.
- Use multimeter to test continuity; if no continuity, replace igniter.
- Reassemble dryer and test cycle.
Check gas supply and valve position
- Verify main gas valve at house is fully open.
- Check gas line for kinks or obvious damage.
- Attempt a test cycle with proper gas supply.
Next step
Choose the next step for not igniting
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Gas Valve
Controls the flow of natural gas or propane to the burner jets.
- Typical part-only price
- $60 - $140
- DIY difficulty
- Hard
- Estimated time
- 45-60 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Flame Sensor
Confirms burner flame or radiant heat so the appliance can control gas flow safely.
Thermal Fuse
A safety device that cuts off power to the appliance if it starts to overheat.
Model-compatible Dryer parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dryer Vent Cleaning Kit
Helps remove routine lint buildup from an accessible dryer vent path. It does not diagnose or repair an E-code or failed component.
Lint Trap Cleaning Brush
A narrow brush for routine cleaning around an accessible lint screen and housing.
Dryer Vent Hose Kit
A replacement exhaust duct option for visibly crushed or damaged external venting. Check diameter, length, local code, and installation clearance.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace gas valve solenoid coils
Flame sensor replacement and calibration
When to Call a Professional
Preventive Maintenance
-
Clean lint filter and venting regularly: Vent blockage that can affect heat and combustion efficiency
Frequency: after every use -
Inspect gas connections annually: Gas supply issues that prevent ignition
Frequency: annually
Frequently Asked Questions
Why is my Samsung Dryer not igniting?
How do I fix Samsung Dryer not igniting myself?
How much does it cost to fix not igniting?
When should I call a technician for not igniting?
References & Sources
- Samsung gas dryer troubleshooting Community
- How to test Samsung dryer igniter Repair-Blog
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Faulty igniter
- Clogged gas line
- Defective flame sensor
User Suggested Solutions
-
Inspect and replace the igniter. Unplug the dryer, remove the front panel, and locate the igniter. Test it for continuity with a multimeter. If it's faulty, replace it with a new one.
-
Check and clear the gas line. Ensure that the gas supply is turned on and inspect the line for any blockages. If you find a clog, clear it or replace the line if necessary.
-
Test and replace the flame sensor. Unplug the dryer, access the flame sensor, and check for continuity. If it’s defective, replace it to restore functionality.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!