Miele Dishwasher: not heating
What is this symptom?
Is your Miele dishwasher running but not heating the water? If dishes come out cold or lukewarm, this could be due to a faulty heating element, thermostat, or control circuit. Addressing this issue promptly is essential to ensure your dishes are properly cleaned and sanitized.
Important Tips for Miele Models
- Some Miele models display error code F24 to indicate a heating fault involving element, flow heater, wiring or relay.
Possible Causes
Faulty heating element / flow‑through heater
How to Identify: Dishwasher completes wash cycle with water cold; resistance test of heater shows out‑of‑range values; visible damage/calcification.
Part: Heating element / flow heater
Faulty thermostat / temperature sensor
How to Identify: Dishwasher does not signal heater activation; multimeter test shows open or incorrect readings.
Part: Thermostat / temperature sensor
Heating relay or control circuit failure
How to Identify: No voltage delivered to heating element despite correct signals; possible error code displayed (e.g., F24.
Part: Heater relay / control board
Insufficient water temperature supply or water routing issues
How to Identify: Incoming hot water supply too low; low water volume affecting heat buildup.
Part: Water inlet / plumbing
DIY Solutions
Inspect and test heating element
- Disconnect power to dishwasher.
- Access lower panel to reach the heating element.
- Visually inspect element for damage or calcification.
- Use a multimeter to measure resistance.
- Replace the element if reading is open/no continuity.
Check thermostat/temperature sensor
- Disconnect power.
- Locate thermostat/sensor beneath dishwasher.
- Test with multimeter for correct continuity.
- Replace if faulty.
Verify water supply temperature and plumbing
- Ensure hot water faucet runs hot before starting dishwasher.
- Check that water inlet hose is not kinked or blocked.
Next step
Choose the next step for not heating
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Heating Element
Heats the water or air inside the appliance to the required temperature.
- Typical part-only price
- $40 - $95
- DIY difficulty
- Medium
- Estimated time
- 30-45 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Temperature Sensor
Monitors the internal temperature to ensure correct operation and prevent overheating.
Thermostat
Regulates temperature by turning the heating or cooling system on or off.
Main Control Board
The central brain of the appliance that controls all components, cycles, and timings.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace heating element (professional)
Control board / heater relay repair
When to Call a Professional
Preventive Maintenance
-
Run dishwasher on hottest cycle periodically: Mineral buildup on heating element and ensures internal parts stay functional.
Frequency: monthly -
Clean spray arms and filters: Distribution issues that can affect heat transfer.
Frequency: monthly
Frequently Asked Questions
Why is my Miele Dishwasher not heating?
How do I fix Miele Dishwasher not heating myself?
How much does it cost to fix not heating?
When should I call a technician for not heating?
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Faulty heating element
- Defective thermostat
- Malfunctioning control board
User Suggested Solutions
-
Test and replace the heating element: 1) Unplug the dishwasher. 2) Access the heating element by removing the lower spray arm and cover. 3) Use a multimeter to check for continuity. 4) If faulty, replace the heating element with a new one. 5) Reassemble and test the dishwasher.
-
Check and replace the thermostat: 1) Unplug the dishwasher. 2) Locate the thermostat (usually near the heating element). 3) Test it with a multimeter for continuity. 4) If defective, remove and replace it. 5) Reassemble and test the dishwasher.
-
Inspect and replace the control board: 1) Unplug the dishwasher. 2) Access the control board (usually behind the front panel). 3) Check for burnt components or loose connections. 4) If damaged, replace the control board. 5) Reassemble and test the dishwasher.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!