LG Oven: not stopping when using convection bake

Professional Repair Guide

What is this symptom?

Is your LG oven not stopping when using the convection bake mode? This issue may arise when the convection fan continues to run beyond the set baking time. While it's normal for the fan to operate until the internal temperature cools, persistent operation could indicate an underlying problem. Understanding the causes and solutions can help you address this issue effectively.

Urgency: Medium

Important Tips for LG Models

  • LG convection modes automatically reduce temperature and circulate air; fans running during convection bake is normal and may continue until cooling.

Possible Causes

Normal convection fan operation during cooking

How to Identify: Fan running during active cooking is expected; cycling on/off as oven maintains set temperature is normal.

Part: Convection fan

DIY Solutions

Verify correct cycle end and settings

Easy 5-10 minutes
  1. Make sure convection bake cycle and time were properly set and Start/Confirm pressed.
  2. Observe if fan cycles off shortly after reaching set time — fan may run until internal temp cools.
⚠️ Safety First: Ensure oven is cool before inspecting.

Reset the oven electronics

Easy 5 minutes
Tools Needed: None
  1. Turn off oven and disconnect power (unplug or breaker off).
  2. Wait a few minutes to allow electronics to reset.
  3. Reconnect power and try running a convection bake cycle again.
⚠️ Safety First: Ensure power is disconnected before resetting.

Next step

Choose the next step for not stopping when using convection bake

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Non-Scratch Cooktop Cleaner

A routine surface-care product. Confirm that it is approved for the specific glass, ceramic, enamel, or stainless finish.

View maintenance supply
Diagnostic tool

Oven Thermometer

A diagnostic aid for comparing cavity temperature during a controlled check. It does not prove which internal component has failed.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace thermostat/temperature sensor

Estimated Cost: $40 - $120

Control board replacement

Estimated Cost: $200 - $450

When to Call a Professional

Oven continues heating unabated after cycle end
Error codes displayed with convection mode
Unusual noises, burning smells, or electrical issues occur during operation

Preventive Maintenance

  • Keep oven interior and vents clean: Obstructions that can affect airflow and fan function
    Frequency: monthly
  • Inspect control panel for responsiveness: Control glitches that may affect cycle termination
    Frequency: periodically

Frequently Asked Questions

Why is my LG Oven not stopping when using convection bake?
Your LG oven may not stop due to normal fan operation or an issue with the thermostat.
How do I fix LG Oven not stopping when using convection bake myself?
Verify your cycle settings and reset the oven's electronics by disconnecting power.
How much does it cost to fix not stopping when using convection bake?
Professional repairs range from $40 to $450 depending on the issue.
When should I call a technician for not stopping when using convection bake?
Consider calling a technician if DIY solutions do not resolve the issue or if you're unsure.

References & Sources

Community Analytical Insights

Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions

Common Issues Reported by Users

  • Faulty convection fan control board
  • Stuck relay on the control board
  • Defective temperature sensor

User Suggested Solutions

  1. Inspect and replace the convection fan control board. Unplug the oven, remove the back panel, locate the control board, and check for signs of damage or burnt components. Replace if necessary.

  2. Check for a stuck relay on the control board. Access the control board, test the relays with a multimeter, and replace any that are malfunctioning.

  3. Test and replace the temperature sensor if faulty. Locate the sensor, disconnect it, and use a multimeter to check its resistance. Replace if it does not meet specifications.

Limited-source guidance; percentages and success-rate claims are not shown
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. My oven works fine when I use the bake function, but when I ...

User Comments (0)

Share your experience or solution below.

Be the first to comment!

Call Local Repair Provider +1 (888) 217-6318