Kenmore Washer Dryer: leaking
What is this symptom?
Is your Kenmore Washer Dryer leaking water? You may notice puddles on the floor during wash or dry cycles. Common leak sources include loose hoses, a faulty drain pump, or damaged seals. Identifying the problem early can prevent further water damage and costly repairs.
Possible Causes
Loose or damaged water inlet fill hoses
How to Identify: Water pooling near back of machine during fill cycle; visible drips from hose connections
Part: Inlet hoses (hot/cold)
Faulty or cracked drain hose
How to Identify: Water leaking from bottom rear; hose visible wear/cracks; leaks more during drain
Part: Drain hose
Leaking drain pump
How to Identify: Water under machine during or after draining, visible cracks at pump housing
Part: Drain pump
Worn or damaged tub-to-pump hose
How to Identify: Leaks from middle-bottom; hose cracks/bulges visible upon inspection
Part: Tub-to-pump hose
Damaged door boot seal (front-load models)
How to Identify: Water around front door area especially during wash/spin; visible gasket tears or mold deterioration
Part: Door boot gasket
Next step
Choose the next step for leaking
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
- Typical part-only price
- $15 - $30
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
Door Gasket
Creates a watertight seal around the door to prevent leaks during operation.
Model-compatible Washer Dryer parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dryer Vent Cleaning Kit
Helps remove routine lint buildup from an accessible dryer vent path. It does not diagnose or repair an E-code or failed component.
Lint Trap Cleaning Brush
A narrow brush for routine cleaning around an accessible lint screen and housing.
Dryer Vent Hose Kit
A replacement exhaust duct option for visibly crushed or damaged external venting. Check diameter, length, local code, and installation clearance.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Preventive Maintenance
-
Inspect hoses and clamps: Hose cracks and leak failures
Frequency: annually -
Clean drain pump filter: Clogs leading to leaks or poor drainage
Frequency: every 3-6 months
Frequently Asked Questions
Why is my Kenmore Washer Dryer leaking?
How do I fix Kenmore Washer Dryer leaking myself?
How much does it cost to fix leaking?
When should I call a technician for leaking?
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Worn or damaged door seal/gasket
- Clogged or damaged drain pump
- Loose or damaged hoses (inlet or drain)
User Suggested Solutions
-
Inspect and replace the door seal/gasket. Ensure the door is closed properly and check for any visible wear or tears. If damaged, purchase a replacement and install it by removing the old gasket and securing the new one in place.
-
Check the drain pump for clogs or damage. Disconnect the power, remove the drain pump cover, and inspect for debris. Clean or replace the pump if necessary.
-
Inspect all hoses for leaks. Tighten any loose connections and replace any damaged hoses. Ensure that the inlet hoses are properly connected and not kinked.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
started leaking
Repairing the Kenmore is recommended as it can last another 15 years; a bad pump is likely the issue.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!