Hotpoint Dishwasher: not stopping and making gurgling noise

Professional Repair Guide

What is this symptom?

Is your Hotpoint dishwasher continuously running and making a gurgling noise? This issue often arises during drain cycles, indicating potential problems like a clogged drain system, a faulty float switch, or issues with the control board. Understanding these causes is key to restoring your dishwasher's functionality.

Urgency: Medium

Important Tips for Hotpoint Models

  • Noise and drain issues are commonly linked with drain pump or impeller problems on various Hotpoint models

Possible Causes

Clogged drain system or filter

How to Identify: Water pools or drains slowly; gurgling sound increases when draining; filter visibly blocked when removed.

Part: Drain hose / filter / pump intake

Faulty or stuck float switch or water level sensor

How to Identify: Dishwasher continues running because it incorrectly detects water level; motor does not stop; multimeter continuity test fails.

Part: Float switch / water level sensor

Control board or timer malfunction

How to Identify: Dishwasher runs beyond normal cycle lengths or behaves erratically; resetting power sometimes temporarily resolves.

Part: Electronic control board / timer

Air gap or improper drain hose installation

How to Identify: Gurgling noise correlated with sink drain or improper high loop/air gap setup; visible hose kinks.

Part: Air gap / drain hose

Pump or motor assembly wear or debris

How to Identify: Noises beyond gurgling such as grinding; appliance struggles to push water out; debris visible on impeller.

Part: Drain pump / circulation pump

DIY Solutions

Clean filter and drain path

Moderate 15-30 minutes
Tools Needed: screwdriver, gloves, bucket
  1. Turn off the dishwasher and power at the breaker.
  2. Remove lower rack to access and remove filter assembly.
  3. Rinse filter under running water and clear any debris.
  4. Inspect bottom of dishwasher and remove visible debris near drain.
  5. Run a short rinse cycle to test if noise and continuous run improve.
⚠️ Safety First: Ensure power is off before working inside appliance

Check and clear drain hose and air gap

Advanced 30-60 minutes
Tools Needed: screwdriver, bucket, pliers
  1. Turn off power and water supply.
  2. Access the drain hose under the sink; check for kinks or clogs.
  3. Remove hose and flush with water to clear blockages.
  4. If equipped, check and clean sink air gap from top down.
  5. Reinstall hose ensuring proper high loop or air gap setup.
⚠️ Safety First: Be prepared for water spillage when disconnecting drain hose

Power cycle/reset the dishwasher

Easy 5-10 minutes
  1. Switch off the dishwasher at the breaker or unplug.
  2. Wait 5–10 minutes to allow the control board to reset.
  3. Restore power and run a short cycle to see if it completes.

Next step

Choose the next step for not stopping and making gurgling noise

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Check during diagnosis

Most relevant component to inspect

Drain Hose

Carries waste water from the drain pump to your home's standpipe or sink drain.

Typical part-only price
$15 - $30
DIY difficulty
Easy
Estimated time
15-30 mins
Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Possible related component

Float Switch

Detects the maximum water level to prevent overflow and potential flooding.

$15 - $40 · Easy · 10-20 mins

Check fit & price
Possible related component

Pressure Switch

Detects the water level inside the tub and signals when to start or stop filling.

$25 - $65 · Easy · 15-30 mins

Check fit & price
Possible related component

Main Control Board

The central brain of the appliance that controls all components, cycles, and timings.

$120 - $280 · Medium · 20-40 mins

Check fit & price
Model number required

Model-compatible Dishwasher parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Dishwasher Cleaner and Descaler

Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.

View maintenance supply
Maintenance supply

Braided Dishwasher Inlet Hose

For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace drain pump or motor assembly

Estimated Cost: $100 - $300

Replace float switch or level sensor

Estimated Cost: $50 - $150

Control board or timer replacement

Estimated Cost: $200 - $500

When to Call a Professional

Persistent gurgling and nonstop operation after DIY drain and filter cleaning
Visible damage to hoses, pumps, or components
Electrical faults or control board issues suspected

Preventive Maintenance

  • Clean filter and drain area: Clogs that cause gurgling and incomplete drain
    Frequency: monthly
  • Check drain hose routing: Improper installation that can cause gurgling and backflow
    Frequency: annually

Frequently Asked Questions

Why is my Hotpoint Dishwasher not stopping and making gurgling noise?
Common causes include a clogged drain system, a faulty float switch, or a malfunctioning control board.
How do I fix Hotpoint Dishwasher not stopping and making gurgling noise myself?
Try cleaning the filter and drain path, checking the drain hose, or resetting the dishwasher.
How much does it cost to fix not stopping and making gurgling noise?
Professional repair costs can range from $50 to $500 depending on the issue.
When should I call a technician for not stopping and making gurgling noise?
Call a technician if DIY solutions don't resolve the issue or if the problem seems complex.

References & Sources

Community Analytical Insights

Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions

Common Issues Reported by Users

  • Faulty door latch or switch preventing the dishwasher from stopping
  • Clogged drain hose causing water to back up and gurgle
  • Malfunctioning control board or timer causing continuous operation

User Suggested Solutions

  1. Inspect and replace the door latch or switch. Ensure the door is properly closed and the latch engages. If faulty, replace the latch or switch.

  2. Check the drain hose for clogs or kinks. Remove any obstructions and ensure the hose is properly positioned to allow for drainage.

  3. Test the control board or timer for faults. If malfunctioning, consider replacing the control board. Consult the manual for specific testing procedures.

Limited-source guidance; percentages and success-rate claims are not shown
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Hotpoint LFT228A

User Comments (0)

Share your experience or solution below.

Be the first to comment!