Haier Washing Machine: error code displayed

Professional Repair Guide

What is this symptom?

Is your Haier washing machine displaying an error code on the control panel? This can indicate various issues, such as a door lock failure, drainage blockage, or sensor faults. The machine may stop mid-cycle, making it crucial to identify the underlying cause to restore functionality and prevent further damage.

Urgency: Medium

Possible Causes

Door/lid not closed or door lock failure

How to Identify: Codes like E0/E2 often relate to lid/door open detection errors; machine won’t start or continues blinking until door properly engaged.

Part: Door/lid switch / latch

Drainage blockage or pump filter issue

How to Identify: Error codes related to drainage (e.g., E1 or Err2 with water remaining in drum and no draining action.

Part: Drain pump filter, drain hose

Internal sensor or electronics fault

How to Identify: Codes like E6, E8, E9, FA, FC often indicate sensor abnormalities; resetting may temporarily clear but recurring codes suggest internal fault.

Part: Control board / sensors

Motor overheat or motor damage

How to Identify: Err7 reportedly indicates motor overheat or damage with machine ceasing operation.

Part: Motor / motor circuits

Next step

Choose the next step for error code displayed

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Door or Lid Switch

Detects whether the appliance door or lid is safely closed before operation.

Typical part-only price: $15 - $55
DIY difficulty: Medium
Estimated time: 20-45 mins

Optional: enter your model number

Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other components that may be involved

Check these only if your diagnosis points to them.

Possible related component

Drain Pump

Pumps waste water out of the appliance during the drain cycle.

$35 - $80 · Easy · 15-30 mins

Check fit & price

Possible related component

Main Control Board

The central brain of the appliance that controls all components, cycles, and timings.

$120 - $280 · Medium · 20-40 mins

Check fit & price

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Preventive Maintenance

Clean drain pump filter: Drainage blockages and related error codes
Frequency: monthly
Check hoses for kinks and wear: Water supply/fill errors and leaks
Frequency: quarterly
Avoid overloading and balance loads: Vibration and unbalanced load errors
Frequency: every wash

Frequently Asked Questions

Why is my Haier Washing Machine error code displayed?

Common reasons include a door not closed properly, drainage issues, or sensor faults.

How do I fix Haier Washing Machine error code displayed myself?

Currently, there are no DIY solutions available for this issue.

How much does it cost to fix error code displayed?

Repair costs can vary based on the specific fault and technician rates.

When should I call a technician for error code displayed?

Call a technician if the error persists or if you're unable to identify the issue.

References & Sources

Haier Washing Machine Error Codes (Japan Support) Official
Haier washing machine error explanations Community

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

60%

DIY Success Rate Difficulty: Either

Common Issues Reported by Users

Faulty door lock mechanism preventing the machine from operating correctly
Blocked or malfunctioning drain pump causing the error to trigger
Water level sensor issues leading to incorrect readings and error display

User Suggested Solutions

Inspect and replace the door lock mechanism: Unplug the machine, remove the front panel, check the door lock for damage, and replace if necessary.
Check and clean the drain pump: Unplug the machine, locate the drain pump, remove any blockages, and test the pump for functionality.
Test and replace the water level sensor: Unplug the machine, access the sensor, check for continuity with a multimeter, and replace if faulty.