Haier Washer Dryer: not stopping filling

Professional Repair Guide

What is this symptom?

Is your Haier washer dryer continuously filling with water? This issue can lead to overfilling and potential water damage. The most common cause is a faulty water inlet valve stuck in the open position, preventing the unit from stopping at the correct water level. Don't let this problem worsen; take action to resolve it quickly.

Urgency: High

Important Tips for Haier Models

Official troubleshooting documentation lists continuous filling under general filling issues (though specific causes not detailed) and recommends professional assistance if standard troubleshooting doesn’t help.

Possible Causes

Faulty water inlet valve stuck open

How to Identify: Water continues flowing into the tub even when the machine should have stopped filling; shutting off power does not immediately stop water flow (after turning off water supply.

Part: Water Inlet Valve

DIY Solutions

Inspect and replace water inlet valve

Moderate 30-60 minutes

Tools Needed: screwdriver, multimeter, replacement inlet valve

Unplug washer and shut off water supply.
Remove rear panel to access water inlet valve.
Disconnect hoses and inspect screens for debris; clean if clogged.
Test valve solenoids with multimeter; if stuck open, replace with new valve.
Reassemble and test machine.
Restore power and water supply.

⚠️ Safety First: Always disconnect power and water supply before servicing.

Check and clear/replace pressure hose and switch

Moderate 45-90 minutes

Tools Needed: screwdriver, multimeter, possibly replacement pressure hose/switch

Disconnect power and water.
Access pressure switch and hose inside unit.
Inspect pressure hose for kinks, blockages, or damage.
Clean or replace hose as needed.
Test pressure switch continuity with multimeter; replace if faulty.
Reassemble and test.

⚠️ Safety First: Turn off power before opening panels.

Next step

Choose the next step for not stopping filling

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Based on diagnostic data

Most relevant component to inspect

Water Inlet Valve

Controls the flow of hot and cold water into the appliance.

Typical part-only price: $25 - $60
DIY difficulty: Easy
Estimated time: 15-30 mins

Optional: enter your model number

Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Professional Repairs

Control board and electronics diagnosis/replacement

Estimated Cost: $150 - $400+

Pressure switch replacement

Estimated Cost: $50 - $150

When to Call a Professional

Water continues filling despite shutting off power and you cannot identify obvious parts issues

Signs of electrical damage or burnt components on control board

Uncertainty about safely accessing internal components

Preventive Maintenance

Clean inlet hose screens: Debris buildup that can lead to inlet valve issues
Frequency: annually
Inspect pressure hose and connections: False readings leading to overfilling
Frequency: annually

Frequently Asked Questions

Why is my Haier Washer Dryer not stopping filling?

The most common cause is a faulty water inlet valve that is stuck open.

How do I fix Haier Washer Dryer not stopping filling myself?

You can inspect and replace the water inlet valve or check the pressure hose and switch for blockages.

How much does it cost to fix not stopping filling?

Professional repairs can range from $50 to $400+, depending on the issue.

When should I call a technician for not stopping filling?

If DIY solutions don't resolve the issue, or if you suspect a control board problem, it's best to call a technician.

References & Sources

How to fix a washer that won't stop filling with water Community
Stop the Flow: How to Fix a Washing Machine That Keeps Filling With Water Repair-Blog
Haier Support – Washing Machine Filling Continuously Official

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

75%

DIY Success Rate Difficulty: DIY

Common Issues Reported by Users

Faulty water inlet valve causing continuous water flow
Defective pressure switch not detecting water level
Clogged or kinked drain hose affecting pressure readings

User Suggested Solutions

Inspect and replace the water inlet valve. Disconnect power and water supply, remove the valve, and check for continuity with a multimeter. Replace if defective.
Test and replace the pressure switch. Locate the pressure switch, disconnect the hose and electrical connector, and test for continuity. Replace if faulty.
Check and clear any clogs in the drain hose. Inspect the hose for kinks or blockages and ensure it is properly positioned to allow for drainage.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

Front load washer dryer keeps filling with water when off

Community Discussions

keeps filling with water when off

The issue is likely a machine problem rather than a plumbing issue, as the washer should not fill when off.