GE Washing Machine: not stopping filling
What is this symptom?
Is your GE washing machine not stopping filling with water? This common issue can result in overflow, as water keeps entering the tub even if a cycle hasn't started. The problem is often due to a faulty water inlet valve or a defective water level switch. Address this quickly to prevent water damage and ensure efficient operation.
Important Tips for GE Models
- GE support specifically notes improper drain hose height (must be >30 inches) can cause continuous fill behavior due to backflow. (GE Appliances
- AppliancePartsPros community data shows water level switch and water inlet valve are top causes for GE WDSR2080DAWW continuous fill symptom.
Possible Causes
Faulty water inlet valve stuck open
How to Identify: Continuous water entry even when machine is off or cycle has not progressed; water still flows when power is disconnected from control circuits; valve may fail to close.
Part: Water Inlet Valve (solenoid)
Defective water level (pressure) switch or pressure switch hose issue
How to Identify: Washer cannot correctly detect water level; pressure switch hose may be cracked/clogged leading to false low-water signals and continuous fill.
Part: Water Level Switch / Pressure Switch Hose
DIY Solutions
Check and reposition drain hose to stop siphoning
- Ensure the drain hose is raised at least 30 inches above floor level.
- Secure the hose in a proper standpipe or laundry tub to prevent water backflow.
- Run a test cycle to confirm whether siphoning/backflow issue is resolved.
Inspect and clean inlet valve screens
- Turn off water supply to washer.
- Disconnect inlet hoses from back of washer.
- Inspect the small mesh screens inside the water inlet valve ports for dirt/debris.
- Clean screens with brush and water, then reconnect hoses.
- Turn on water supply and test washer fill behavior.
Next step
Choose the next step for not stopping filling
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
- Typical part-only price
- $25 - $60
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Pressure Switch
Detects the water level inside the tub and signals when to start or stop filling.
Model-compatible Washing Machine parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Washing Machine Cleaner Tablets
Routine tub-cleaning supplies for residue and odor control. They do not repair a mechanical, drainage, or electronic fault.
Braided Washer Inlet Hoses
A maintenance replacement option for visibly worn external fill hoses. Verify thread size, length, and hot/cold connection requirements.
Washer Drain Hose Holder
Helps secure an external drain hose at the standpipe. It does not correct an internal pump or control fault.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace water inlet valve assembly
Replace water level switch or pressure switch hose
Control board diagnosis and replacement
When to Call a Professional
Preventive Maintenance
-
Regularly clean inlet hose screens: Debris buildup causing inlet valve sticking.
Frequency: annually -
Check drain hose positioning: Siphoning/backflow causing perceived overfill.
Frequency: each installation or move
Frequently Asked Questions
Why is my GE Washing Machine not stopping filling?
How do I fix GE Washing Machine not stopping filling myself?
How much does it cost to fix not stopping filling?
When should I call a technician for not stopping filling?
References & Sources
- Washer - Will Not Stop Filling Official
- How to fix a washer that won’t stop filling with water Repair-Blog
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Faulty water inlet valve
- Clogged or kinked fill hose
- Defective pressure switch
User Suggested Solutions
-
Inspect and replace the water inlet valve. Unplug the washing machine, turn off the water supply, remove the back panel, and replace the valve if it shows signs of damage or malfunction.
-
Check the fill hose for clogs or kinks. Disconnect the hose from the machine and inspect for blockages, cleaning or replacing as necessary.
-
Test and replace the pressure switch. Access the control panel, locate the pressure switch, and use a multimeter to check for continuity. Replace if faulty.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
won’t stop filling and keeps overflowing
Check and clean the clear hose attached to the tub for blockages.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!