GE Washer Dryer: noisy operation, faulty bearings, faulty inverter boards, latch error, fault code 353
What is this symptom?
Is your GE washer dryer combo making unusual noises during the spin cycle? You might be facing issues like worn tub bearings or a clogged lint filter, leading to fault code 353 or latch errors. Addressing these problems promptly can enhance performance and prevent further damage.
Important Tips for GE Models
- Error code 353 most often means a clogged lint filter which should be cleaned regularly per GE documentation.
- Bearing replacement is complex and often requires professional disassembly.
Possible Causes
Worn/damaged tub bearings or related drum support
How to Identify: Loud rumbling or roaring noise during spin; noise increases with drum rotation; possible leaking at bottom of tub; imbalance not resolved by load changes
Part: tub bearing / drum
Clogged lint filter causing error code 353 and drying airflow restriction
How to Identify: Error 353 on display; drying cycle interrupted or ineffective drying; lint buildup visible in mesh filter and foam filter
Part: lint filter / foam filter
Off‑balance load causing excessive vibration/noise
How to Identify: Noise only during certain cycles; stops/change load balance reduces noise
Part: drum/load distribution
Shock absorbers or suspension components worn
How to Identify: Thumping or banging noise during agitation/spin consistent with tub movement hitting cabinet
Part: shock absorbers / suspension rods
Faulty moisture sensor or airflow blockage causing secondary 353 errors
How to Identify: Error 353 persists after lint cleaning; moisture sensor bars show residue or damage
Part: moisture sensor
DIY Solutions
Clean lint filter and foam filter
- Pull out lint filter assembly from Combo washer/dryer
- Separate foam filter from mesh and rinse with warm water
- Use soft brush to remove lint and residue from mesh filter
- Allow parts to dry and reinstall into filter frame
Balance laundry load to reduce noise
- Stop machine and redistribute laundry evenly around drum
- Avoid mixing very heavy and very light items in same load
- Add additional items to balance small loads
Next step
Choose the next step for noisy operation, faulty bearings, faulty inverter boards, latch error, fault code 353
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drum Bearing Kit
Supports the spinning drum and ensures smooth, quiet rotation during cycles.
- Typical part-only price
- $40 - $95
- DIY difficulty
- Hard
- Estimated time
- 120-180 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Dryer Lint Filter
Captures lint from exhaust air before it reaches the dryer vent path.
Washer Shock Absorber
Dampens tub movement and vibration during high-speed spin cycles.
Washer Suspension Rod Kit
Supports and stabilizes the washer tub during agitation and spin.
Model-compatible Washer Dryer parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dryer Vent Cleaning Kit
Helps remove routine lint buildup from an accessible dryer vent path. It does not diagnose or repair an E-code or failed component.
Lint Trap Cleaning Brush
A narrow brush for routine cleaning around an accessible lint screen and housing.
Dryer Vent Hose Kit
A replacement exhaust duct option for visibly crushed or damaged external venting. Check diameter, length, local code, and installation clearance.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Professional Repairs
Replace tub bearings and outer drum assembly
Replace moisture sensor or advanced drying components
When to Call a Professional
Preventive Maintenance
-
Clean lint filter: Error code 353 and drying airflow issues
Frequency: every 5 dry cycles -
Check load balance: Noise from imbalance and wear on bearings/suspension
Frequency: each wash
Frequently Asked Questions
Why is my GE Washer Dryer noisy operation, faulty bearings, faulty inverter boards, latch error, fault code 353?
How do I fix GE Washer Dryer noisy operation, faulty bearings, faulty inverter boards, latch error, fault code 353 myself?
How much does it cost to fix noisy operation, faulty bearings, faulty inverter boards, latch error, fault code 353?
When should I call a technician for noisy operation, faulty bearings, faulty inverter boards, latch error, fault code 353?
References & Sources
Community Analytical Insights
Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions
Common Issues Reported by Users
- Worn drum bearings causing excessive noise during operation
- Faulty inverter board leading to erratic motor function and noise
- Front latch error due to misalignment or wear, causing operational interruptions
- Fault code 353 indicating a communication error between the control board and the motor
User Suggested Solutions
-
Inspect and replace worn drum bearings. Disassemble the washer dryer unit, remove the drum, and replace the bearings. Reassemble and test for noise reduction.
-
Test the inverter board for faults using a multimeter. If faulty, replace the inverter board. Ensure proper connections are secured before testing.
-
Check and realign the front latch mechanism. Ensure that the latch is not obstructed and is properly seated. Test the unit to confirm the error is resolved.
-
Reset the washer dryer by unplugging it for 5 minutes. If fault code 353 persists, further diagnostics may be needed on the control board.
Limited-source guidance; percentages and success-rate claims are not shown
View
Sources
Data compiled from real discussions on r/appliancerepair and r/Appliances:
Community Discussions
noisy operation, drum bearings shot, inverter boards dying, front latch errors, 353 fault code
Replaced unit with a new Samsung washer/dryer combo after deciding against repairs.
Source: Reddit r/appliancerepair
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!