Electrolux Freezer: broken ice maker component

Professional Repair Guide

What is this symptom?

If your Electrolux freezer's ice maker isn't producing ice, it may be due to a broken component. Common issues include a faulty ice maker assembly, blocked water inlet valve, or incorrect freezer temperature settings. Understanding these causes can help you troubleshoot effectively and restore ice production quickly.

Urgency: Medium

Important Tips for Electrolux Models

  • Electrolux often does not sell ice maker subcomponents separately, requiring full assembly replacement

Possible Causes

Faulty ice maker assembly or internal component failure

How to Identify: Ice maker doesn’t cycle, no sounds from motor, visible broken/misaligned parts when inspected

Part: Ice maker assembly (including motor, ejector arms, internal gears)

Water inlet valve failure or blockage

How to Identify: No water filling ice maker, low water pressure, multimeter test shows no power or valve not opening

Part: Water inlet valve

Clogged water filter

How to Identify: Reduced water dispenser flow, filter older than 6 months, ice maker not filling properly

Part: Water filter

Incorrect freezer temperature

How to Identify: Freezer warmer than –18°C, slow or no ice production

Part: Freezer thermostat/temperature control

Ice level control sensor or control board malfunction

How to Identify: Ice maker doesn’t turn on despite proper conditions, control board inspection shows faults or sensor errors

Part: Ice level control board/sensors or main control board

DIY Solutions

Inspect and clear frozen fill tube or water line

Moderate 15-30 minutes
Tools Needed: hairdryer, towels
  1. Turn off water supply and ice maker.
  2. Use a hairdryer to gently warm the fill tube to thaw any ice blockage.
  3. Straighten any kinks in the water line to ensure proper flow.
  4. Turn water supply and ice maker back on and test function.
⚠️ Safety First: Avoid overheating or holding hairdryer too close to components.

Replace water filter

Easy 10-15 minutes
Tools Needed: replacement water filter
  1. Locate the water filter (per model manual).
  2. Remove old filter and install new Electrolux-approved filter.
  3. Run water through dispenser to purge system.
  4. Check if ice maker begins filling cycles.

Verify and adjust freezer temperature

Easy 5 minutes
Tools Needed: freezer thermometer
  1. Place a thermometer in freezer to measure temperature.
  2. Adjust thermostat to target around 0°F.
  3. Allow several hours for temperature to stabilize and check ice production.

Next step

Choose the next step for broken ice maker component

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Check during diagnosis

Most relevant component to inspect

Ice Maker Assembly

Automatically freezes and dispenses ice cubes inside the freezer compartment.

Typical part-only price
$75 - $160
DIY difficulty
Medium
Estimated time
20-30 mins
Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Possible related component

Water Inlet Valve

Controls the flow of hot and cold water into the appliance.

$25 - $60 · Easy · 15-30 mins

Check fit & price
Possible related component

Water Filter

Filters out impurities, sediment, and chlorine taste from your drinking water and ice.

$25 - $45 · Easy · 5 mins

Check fit & price
Possible related component

Thermostat

Regulates temperature by turning the heating or cooling system on or off.

$15 - $40 · Easy · 15-30 mins

Check fit & price
Model number required

Model-compatible Freezer parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Refrigerator Condenser Coil Brush

For routine cleaning of accessible condenser areas where the manufacturer permits it. It does not repair a sealed-system or compressor fault.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Replace ice maker assembly

Estimated Cost: $100 - $200

Replace water inlet valve

Estimated Cost: $50 - $120

Diagnose and repair control board or sensor issues

Estimated Cost: $150 - $300

When to Call a Professional

Ice maker assembly components visibly broken or motors not running
Electrical tests show faulty water inlet valve or control board
No improvement after basic DIY checks

Preventive Maintenance

  • Replace water filter: Clogged filter and restricted water flow to ice maker
    Frequency: every 6 months
  • Monitor freezer temperature: Ice production issues from incorrect temperature
    Frequency: monthly

Frequently Asked Questions

Why is my Electrolux Freezer broken ice maker component?
Common causes include faulty ice maker assembly, blocked water inlet valve, or incorrect freezer temperature.
How do I fix Electrolux Freezer broken ice maker component myself?
Inspect the fill tube for ice blockages, replace the water filter, and check the freezer temperature.
How much does it cost to fix broken ice maker component?
Professional repairs cost between $50 to $300, depending on the specific issue.
When should I call a technician for broken ice maker component?
If DIY solutions don't resolve the issue or if the problem involves complex components, contact a technician.

Community Analytical Insights

Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions

Common Issues Reported by Users

  • Ice level sensor lever arm is broken or detached
  • Clogged water line or frozen water inlet valve
  • Faulty ice maker assembly or motor

User Suggested Solutions

  1. Reattach or replace the ice level sensor lever arm. First, unplug the freezer. Remove the ice bucket and inspect the lever arm. If it's broken, replace it with a new part. If it's just detached, reattach it securely. Plug the freezer back in and test the ice maker.

  2. Clear the clogged water line or thaw the frozen water inlet valve. Unplug the freezer, locate the water line, and check for any blockages. If frozen, use a hairdryer on a low setting to gently thaw it. Ensure the water inlet valve is functioning properly and replace if necessary.

  3. Replace the faulty ice maker assembly or motor. Unplug the freezer and remove the ice maker unit. Test the motor for continuity with a multimeter. If faulty, replace the entire ice maker assembly. Reinstall and plug the freezer back in.

Limited-source guidance; percentages and success-rate claims are not shown
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Large plastic piece found in my new freezer's ice bucket?!

Community Discussions

large plastic piece found in ice bucket

The plastic piece is likely the lever arm for the ice level sensor, which can be reattached or replaced.

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!

Call Local Repair Provider +1 (888) 217-6318