None Dishwasher: error code 'Ld'

Professional Repair Guide

What is this symptom?

Experiencing an 'Ld' error code on your dishwasher? This indicates a long drain issue, often causing the wash cycle to stop or repeat. Common causes include clogged drain paths or a kinked drain hose. If your model doesn't list this code, check your manual for guidance.

Urgency: Medium

Important Tips for None Models

  • On GE dishwashers, 'Ld' specifically refers to a long drain condition defined by the control board when expected drainage time is exceeded

Possible Causes

Clogged drain path (filter, pump, or hose)

How to Identify: Standing water at bottom after cycle, partial or no drainage, error 'Ld' persists after reset

Part: Drain filter, drain pump, drain hose

Kinked or improperly routed drain hose

How to Identify: Physical hose inspection reveals bends, compression points, or improper elevation

Part: Drain hose

Wet safety/overflow pan underneath unit triggering sensor

How to Identify: Moisture detected under dishwasher base, unit may not initiate draining normally

Part: Leak/safety sensor and pan

DIY Solutions

Clean the drain filter and pump area

Moderate 15-30 minutes
Tools Needed: Screwdriver (if required for access), Gloves, Bucket/towel
  1. Disconnect power to the dishwasher and turn off water supply.
  2. Open the dishwasher, remove bottom rack, and locate the drain filter assembly.
  3. Remove and clean debris from the filter screen and housing.
  4. If accessible, check the pump area for foreign objects and clear obstructions.
  5. Reassemble the filter, restore power, and run a short cycle to test.
⚠️ Safety First: Ensure power is disconnected before accessing internal components

Inspect and correct drain hose routing

Moderate 10-20 minutes
Tools Needed: Screwdriver or wrench (depending on installation)
  1. Turn off dishwasher power and water supply.
  2. Access the drain hose behind or beneath the unit.
  3. Straighten any kinks and ensure the hose has a high loop or anti‑siphon mechanism.
  4. Check for debris inside the hose; flush with water if possible.
  5. Reattach hose securely and test drain cycle.
⚠️ Safety First: Avoid sharp bends that can restrict flow

Next step

Choose the next step for error code 'Ld'

Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.

Check during diagnosis

Most relevant component to inspect

Drain Hose

Carries waste water from the drain pump to your home's standpipe or sink drain.

Typical part-only price
$15 - $30
DIY difficulty
Easy
Estimated time
15-30 mins
Where can I find the model number?

Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.

Find a part that fits my model

Verify the complete model and part number on the retailer's compatibility page before ordering.

Other parts options

Check related components first; use model search as a fallback.

Possible related component

Drain Pump

Pumps waste water out of the appliance during the drain cycle.

$35 - $80 · Easy · 15-30 mins

Check fit & price
Model number required

Model-compatible Dishwasher parts

Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.

Find a part that fits my model

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.

Optional routine care

Maintenance supplies

These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.

Maintenance supply

Dishwasher Cleaner and Descaler

Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.

View maintenance supply
Maintenance supply

Braided Dishwasher Inlet Hose

For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.

View maintenance supply

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.

Professional Repairs

Drain pump replacement

Estimated Cost: $80 - $200

Leak sensor or safety pan sensor diagnostic and repair

Estimated Cost: $150 - $300+

When to Call a Professional

Drain cleaning and hose routing do not resolve the 'Ld' code
The drain pump makes unusual noises or does not run at all
There is evidence of water leakage under the dishwasher

Preventive Maintenance

  • Clean filter and check drain hose: Clogs leading to long drain issues and error codes
    Frequency: Monthly
  • Inspect under‑unit area for moisture: Potential wet pan triggers and sensor issues
    Frequency: Quarterly

Frequently Asked Questions

Why is my Any Dishwasher Error code 'Ld'?
The 'Ld' error indicates a long drain issue, often due to clogged filters, a kinked drain hose, or a triggered safety pan sensor.
How do I fix Any Dishwasher Error code 'Ld' myself?
To fix it, clean the drain filter and pump area, and inspect the drain hose for kinks or improper routing.
How much does it cost to fix Error code 'Ld'?
Professional repairs for the 'Ld' error can range from $80 to $300+, depending on whether you need a new drain pump or sensor repair.
When should I call a technician for Error code 'Ld'?
If DIY fixes don't resolve the issue or if you're uncomfortable performing repairs, it's best to call a technician.

Community Analytical Insights

Guidance from available sources; statistical claims are shown only for samples of at least 10 discussions

Common Issues Reported by Users

  • Faulty leak sensor detecting water where it shouldn't
  • Clogged drain hose preventing proper drainage
  • Damaged or loose wiring affecting communication between components

User Suggested Solutions

  1. Inspect and clean the leak sensor. Check for any signs of moisture or damage around the sensor area. Replace if necessary.

  2. Examine the drain hose for clogs or kinks. Remove any obstructions and ensure the hose is properly connected.

  3. Check the wiring connections to the leak sensor and other related components. Repair or replace any damaged wires.

Limited-source guidance; percentages and success-rate claims are not shown
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

  1. Ge cafe dishwasher constant beeping “Ld”

Community Discussions

constant beeping with 'Ld' error code

Unplugged for 2 days, cleaned drain, performed software update.

DIY View on Reddit →

Source: Reddit r/appliancerepair

User Comments (0)

Share your experience or solution below.

Be the first to comment!