Bosch Dryer: not spinning

Professional Repair Guide

What is this symptom?

If your Bosch dryer powers on but the drum isn't spinning, your clothes may remain stationary and not tumble. This issue can stem from a broken drive belt, a faulty door latch, or other mechanical failures. Understanding the possible causes can help you resolve the problem effectively.

Urgency: Medium

Important Tips for Bosch Models

Bosch official support recommends checking basic conditions like door closure and contacting support if issue persists; provides limited home troubleshooting.

Possible Causes

Broken or worn drive belt

How to Identify: Drum turns very easily by hand with power off; visible fraying or break in belt.

Part: Drive belt

Faulty door latch/switch

How to Identify: Dryer wonâ€™t start spinning even with correct settings; door may not fully latch.

Part: Door latch/switch

Drive motor malfunction

How to Identify: Humming noise without drum movement; motor does not start.

Part: Drive motor

Blower wheel obstruction

How to Identify: Blockage near blower area; no drum rotation with motor running.

Part: Blower wheel

DIY Solutions

Check and inspect drive belt

Moderate 30-60 minutes

Tools Needed: screwdrivers, socket set

Unplug the dryer.
Remove access panel to view the belt.
Attempt to turn the drum by hand to check tension.
Inspect belt for breaks or wear.
Replace belt if broken and reassemble.

⚠️ Safety First: Always unplug the dryer before opening panels.

Test door latch and switch function

Easy 10-15 minutes

Open and close door to ensure a solid click.
Check for obstructions blocking door closure.
If available, listen for switch click or test with simple press.
If latch seems faulty, order replacement latch and install.

⚠️ Safety First: Do not force door if parts are broken.

Professional Repairs

Replace drum rollers or bearings

Estimated Cost: $80 - $200

Drive motor replacement

Estimated Cost: $120 - $300

Blower wheel clearance or replacement

Estimated Cost: $50 - $150

When to Call a Professional

Drum does not turn despite belt replacement

Humming motor but no rotation

Symptoms of electrical fault or burning smell

Preventive Maintenance

Clean lint filter and interior venting: Lint buildup causing overheating and component stress
Frequency: after every use / monthly vent clean
Regular inspection of belt and rollers: Premature mechanical failure
Frequency: annually

Frequently Asked Questions

Why is my Bosch Dryer not spinning?

Common causes include a broken drive belt, faulty door latch, or drive motor malfunction.

How do I fix Bosch Dryer not spinning myself?

Check the drive belt for damage and test the door latch for proper function.

How much does it cost to fix not spinning?

Professional repairs range from $50 for minor issues to $300 for motor replacement.

When should I call a technician for not spinning?

Call a technician if DIY solutions don't resolve the issue or if you suspect a motor malfunction.

References & Sources

Dryer Drum Not Spinning - Bosch Support Official

Community Analytical Insights

Analysis based on real user discussions from appliance repair communities

Can I Fix This Myself?

65%

DIY Success Rate Difficulty: Either

Common Issues Reported by Users

Belt misalignment or disconnection
Faulty door switch preventing operation
Defective motor or motor relay

User Suggested Solutions

Check and realign the dryer belt. Disconnect power, remove the front panel, and ensure the belt is properly placed over the motor and tensioner. Reassemble and test the dryer.
Test the door switch for continuity. If faulty, replace the door switch. This involves removing the front panel to access the switch.
Inspect the motor and motor relay for signs of wear or failure. If defective, replace the motor. This is a more complex repair that may require professional assistance.

Analysis based on 1 community discussions
View Sources

Data compiled from real discussions on r/appliancerepair and r/Appliances:

Bosch Dryer WTE84106GB not spinning

Community Discussions

not spinning

The issue was due to incorrect belt placement over the tensioner after disassembly.