Defy Dishwasher Error E02
⚡ Quick Answer: The Defy dishwasher E02 error indicates a malfunction related to the drain pump or water fill process. Common symptoms include the dishwasher stopping... ✅ DIY Fixable
What Does Error E02 Mean?
The Defy dishwasher E02 error indicates a malfunction related to the drain pump or water fill process. Common symptoms include the dishwasher stopping at startup, failure to drain water at the end of the cycle, and improper water filling. Potential causes include drainage obstructions or issues with the water inlet valve.
Common Symptoms:
- Dishwasher stops and displays E02 immediately when starting
- Water does not drain properly at end of cycle
- Dishwasher fails to fill with water or detects improper fill
Possible Causes
- Drainage obstruction (community pattern) (medium)
- Water inlet/fill fault (specific Defy reports) (medium)
How to Fix Error E02
DIY Fix Check basic water flow and drain pathways
- Ensure water supply valve to dishwasher is fully open.
- Inspect inlet hose for kinks or blockages.
- Check the drain hose for bends/kinks and ensure it is properly routed.
- Clean dishwasher filter and check for obvious debris in the sump or drain area.
Technician Only Inspect and service drain pump and water inlet components
- Disconnect dishwasher from power.
- Remove and inspect drain pump for blockage or failed impeller.
- Test water inlet valve for correct operation and proper fill timing.
- Verify and clean or replace the drain hose and inlet hose if damaged.
- Check float or water level sensors for correct functionality.
Parts needed: drain pump, water inlet valve, drain hose, inlet hose
- If water continues to remain in the dishwasher after attempted draining and cleaning filters
- If the inlet valve fails to open or water does not enter despite proper supply
- If internal electrical components (pump or valve) show signs of failure
Next step
Choose the next step for E02
Confirm the diagnosis before ordering. An error code can identify the system involved, but it does not prove that a specific part has failed.
Most relevant component to inspect
Drain Pump
Pumps waste water out of the appliance during the drain cycle.
- Typical part-only price
- $35 - $80
- DIY difficulty
- Easy
- Estimated time
- 15-30 mins
Where can I find the model number?
Check the rating label around the door, lid, frame, rear panel, or inside the appliance cabinet. Use the complete model number, including suffixes.
Verify the complete model and part number on the retailer's compatibility page before ordering.
Other parts options
Check related components first; use model search as a fallback.
Water Inlet Valve
Controls the flow of hot and cold water into the appliance.
Drain Hose
Carries waste water from the drain pump to your home's standpipe or sink drain.
Model-compatible Dishwasher parts
Enter the complete model number to browse compatible replacement parts. This is a model-based parts search, not a diagnosis that a specific component failed.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. We may earn a commission from other qualifying purchases or service requests made through links on this page, at no additional cost to you. Recommendations are based on repair relevance, not commission rate.
Optional routine care
Maintenance supplies
These products support cleaning or routine upkeep. They are separate from the possible repair components above and are not claimed to fix this error code or symptom.
Dishwasher Cleaner and Descaler
Supports routine removal of mineral scale, grease, and odor. It is maintenance, not a repair for a failed pump, valve, or control.
Braided Dishwasher Inlet Hose
For replacement of an externally damaged supply hose. Verify connection size, length, and appliance installation requirements before ordering.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Recommendations are based on routine-care relevance, not commission rate.
Technical Specifications
| wattage | 50W |
|---|---|
| component | Drain Pump Assembly |
| resistance | 10-30 ohms |
| part_number | DEFY-DW-PUMP-01 |
| voltage_rating | 230V AC |
Common Questions
What does E02 error mean on defy dishwasher?
E02 indicates a malfunction in the drain pump or water fill process, causing the unit to stop and not drain properly.
Can I fix defy dishwasher E02 error myself?
Yes, check the water supply valve, inspect inlet and drain hoses for blockages or kinks.
How much does it cost to fix E02 error?
Repair costs range from $50 to $200+, depending on parts and labor.
When should I call a technician for E02?
Call if water remains in the dishwasher after draining attempts or if the inlet valve fails to operate.
Data last verified: 2026-07-25
User Comments (0)
Share your experience or solution below.
Please login to post a comment.
Be the first to comment!